Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 65 / 553

background image

VLAN
Type

Configuration
Command

VLAN Description

Application Scenario

MUX
VLAN

To add a MUX VLAN,
run the

vlan vlanid

mux

command.

One MUX VLAN may
contain multiple
upstream ports but only
one service port. The
service ports in different
VLANs are isolated.
One-to-one mapping can
be set up between a MUX
VLAN and an access
user. Hence, a MUX
VLAN can identify an
access user.

MUX VLANs are
applicable to FE or
xDSL service access. For
example, MUX VLANs
can be used to identify
users.

NOTE

l

To add VLANs with consecutive IDs in batches, run the

vlan vlanid to end-vlanid

command.

l

To add VLANs with inconsecutive IDs in batches, run the

vlan vlan-list

command.

Step 2

(Optional) Configure the VLAN attribute.

The default attribute for a new VLAN is "common". You can run the

vlan attrib

command to

configure the attribute of the VLAN.

Configure the attribute according to VLAN planning.

Table 3-10

VLAN attributes and application scenarios

VLA
N
Attri
bute

Configuration
Command

VLAN Type

VLAN
Description

Application
Scenario

Com
mon

The default
attribute for a new
VLAN is
"common".

The VLAN with
this attribute can
be a standard
VLAN, smart
VLAN, or MUX
VLAN.

A VLAN with the
common attribute
can function as a
common layer 2
VLAN or function
for creating a layer
3 interface.

Applicable to the
N:1 access
scenario.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

54

«
...
63
64
65
66
67
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: E-Lins Pages: 59

Brand: E-Lins Pages: 11

Brand: E-Lins Pages: 9

Brand: E-Lins Pages: 5

Network Video Recorders

Brand: e-Line Technology Pages: 34

Module NI PXI-8250

Brand: National Instruments Pages: 39

Brand: Blackrock Microsystems Pages: 27

Nighthawk M6 Pro

Brand: AT&T Pages: 2

Brand: Telex Communications Pages: 28

Brand: Wintech Pages: 21

Brand: 8level Pages: 52

Brand: Glacier Pages: 2

SmartSwitch 8-slot

Brand: Cabletron Systems Pages: 150

Brand: CNC4PC Pages: 11

Brand: Zoom Pages: 31

Brand: Lanner Pages: 141

Brand: Tenda Pages: 82

Brand: Planet Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands