manualshive.com logo in svg

Huawei SmartAX MA5616, Configuration Manual

The Huawei SmartAX MA5616 Configuration Manual is a detailed and comprehensive guide that enables users to efficiently set up and optimize their Huawei SmartAX MA5616. Easily downloadable for free from manualshive.com, this manual provides step-by-step instructions and essential information to maximize your product experience.

Share
Download
background image

Example

To configure software parameter 11 of H.248-based MG interface 0 to 1 so that the MG interface
supports emergency standalone and allows only internal calls, do as follows:

huawei(config)#

interface h248 0

huawei(config-if-h248-0)#

mg-software parameter 11 1

huawei(config-if-h248-0)#

display mg-software parameter 11

                      

  -------------------------------------------------                             
  Interface Id:0           para index:11  value:1                               
  -------------------------------------------------                             
 APPENDIX:                                                                      
  -------------------------------------------------                             
   Interface software parameter name:                                           
   11: Stand alone support                                                      
       0: None                                                                  
       1: Inner                                                                 
       2: Emergency                                                             
       3: Both                                                                  

7.1.1.6 (Optional) Configuring the Ringing Mode of an MG Interface

This topic describes how to configure the ringing mode of an MG interface to meet different
user requirements.

Context

Add the ringing mode mapping records of a specified MG interface. After the adding is
successful, the MG interface can obtains the ringing mode according to the peer parameters
issued by the MGC and then play the ringing to the user in this mode.

Procedure

Step 1

Check whether the ringing mode meets the requirements.

Check whether the preset ringing mode in the system meets the requirements according to the
Usage Guidelines of the 

mg-ringmode add

 command.

l

If the preset ringing mode meets the requirements, go to 

Step 3

.

l

If the preset ringing mode does not meet the requirements, proceed to 

Step 2

.

Step 2

Configure the user-defined ringing mode.

In the global config mode, run the 

user defined-ring modify

 command to configure the break-

make ratio of user-defined ringing mode to form a ringing mode that meets the user requirement.

CAUTION

The system supports 16 user-defined ringing modes, which can be modified but cannot be added
or deleted.

Step 3

Enter the MG interface mode.

Run the 

interface h248

 command to enter the MG interface mode.

Step 4

Add a ringing mapping.

Run the 

mg-ringmode add

 command to add a ringing mapping.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

227

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Alesis QUADRAVERB Service Manual preview
QUADRAVERB
Brand: Alesis Pages: 46
RuggedCom RUGGEDSWITCH RS900G Hardware Installation Manual preview
RUGGEDSWITCH RS900G
Brand: RuggedCom Pages: 23
Western Digital Scorpio WD2500BPVT Product Specifications preview
Scorpio WD2500BPVT
Brand: Western Digital Pages: 3
Western Digital Scorpio WD2500BPVT Product Features preview
Scorpio WD2500BPVT
Brand: Western Digital Pages: 4
Internet Security Systems Proventia A1204 User Manual preview
Proventia A1204
Brand: Internet Security Systems Pages: 42
C&H Active Module Carrier VX402C-64 User Manual preview
Active Module Carrier VX402C-64
Brand: C&H Pages: 32
Renesas RL78/G11 User Manual preview
RL78/G11
Brand: Renesas Pages: 2
Paradyne Hotwire ATM Line Cards 8335 User Manual preview
Hotwire ATM Line Cards 8335
Brand: Paradyne Pages: 132
Cameo WLG-1801 User Manual preview
WLG-1801
Brand: Cameo Pages: 23
AMD Geode LE-366 User Manual preview
Geode LE-366
Brand: AMD Pages: 45
TRENDnet TEW-641PC Quick Installation Manual preview
TEW-641PC
Brand: TRENDnet Pages: 12
Radio Shack Bluespoon 17-1000 Quick Start Manual preview
Bluespoon 17-1000
Brand: Radio Shack Pages: 1
Meinberg CPU-C15G2 Setup Manual preview
CPU-C15G2
Brand: Meinberg Pages: 14
AMC DSP 88 User Manual preview
DSP 88
Brand: AMC Pages: 28
Rajant BreadCrumb ES1 User Manual preview
BreadCrumb ES1
Brand: Rajant Pages: 93
ADTRAN 1202880E1 Quick Start Manual preview
1202880E1
Brand: ADTRAN Pages: 4
SilverStone ECU06 Installation Manual preview
ECU06
Brand: SilverStone Pages: 17
Acces I/O products mPCIE-ADIO16-8F Series Hardware Manual preview
mPCIE-ADIO16-8F Series
Brand: Acces I/O products Pages: 13

Brands by name

Popular brands

Load more brands