manualshive.com logo in svg

Huawei SmartAX MA5616, Configuration Manual

The Huawei SmartAX MA5616 Configuration Manual is a detailed and comprehensive guide that enables users to efficiently set up and optimize their Huawei SmartAX MA5616. Easily downloadable for free from manualshive.com, this manual provides step-by-step instructions and essential information to maximize your product experience.

Share
Download
background image

huawei(config)#

mac-address max-mac-count service-port 1 16

Step 4

In the case of the SHDSL access mode, follow this procedure.
1.

Configure an SHDSL profile. For details, see 

3.7.2 Configuring the SHDSL Profile

. The

ID of the SHDSL line profile is 3, the line rate is 2048 kbit/s, and the profile is used to
activate 4-wire ports.

huawei(config)#

shdsl line-profile quickadd 3 line four-wire rate 2048

2.

Activate the SHDSL port. The port is port 0/4/0, and SHDSL line profile 3 and the default
alarm profile (alarm profile 1) are bound to the port.

NOTE

By default, an ADSL port is in the activated state. Before binding a template to the port, you must deactivate
the port.

huawei(config)#

interface shl 0/4

 

huawei(config-if-shl-0/4)#

deactivate 0

huawei(config-if-shl-0/4)#

activate 0 3

huawei(config-if-shl-0/4)#

alarm-config 0 1

 

huawei(config-if-shl-0/4)#

quit

 

3.

Run the 

display traffic table ip

 command to query the traffic profiles that exist in the

system.

huawei(config)#

display traffic table ip from-index 

0  

                          

{ <cr>|to-
index<K> }:                                                           
                                                                                
  
Command:                                                                      
          display traffic table ip from-index 
0                                 
  
----------------------------------------------------------------------------  
   TID CIR(kbps) CBS(bytes) PIR(kbps) PBS(bytes) Pri Copy-policy    Pri-
Policy  
  
----------------------------------------------------------------------------  
     0      1024      34768      2048      69536   6 -              tag-
pri     
     1      2496      81872      4992     163744   6 -              tag-
pri     
     2       512      18384      1024      36768   0 -              tag-
pri     
     3       576      20432      1152      40864   2 -              tag-
pri     
     4        64       4048       128       8096   4 -              tag-
pri     
     5      2048      67536      4096     135072   0 -              tag-
pri     
     6       off        off       off        off   0 -              tag-
pri     
  
----------------------------------------------------------------------------  
  Total Num : 7        

According to service requirement, the user access rate is 2048 kbit/s. The query result shows
that traffic profile 5 meets the requirement.

NOTE

l

If no traffic profile in the system meets the service requirement, run the 

traffic table ip

 command to

configure a new traffic profile.

l

On the MA5616, the user access rate can be limited by either a traffic profile or an SHDSL line profile.
When both profiles are configured, the user bandwidth adopts the minimum value in the two profiles.
In this example, the traffic profile is used to limit the user access rate.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

331

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

4IPNET WHG301 User Manual preview
WHG301
Brand: 4IPNET Pages: 97
M2M Pro User Manual (Extract preview
Pro
Brand: M2M Pages: 9
Ebyte E43-900T13S3 Manual preview
E43-900T13S3
Brand: Ebyte Pages: 8
JCG Q8 Quick Start Manual preview
Q8
Brand: JCG Pages: 2
IBM AS/400 Hardware User Manual preview
AS/400
Brand: IBM Pages: 104
IBM System Storage TS3100 Setup, Operator, And Service Manual preview
System Storage TS3100
Brand: IBM Pages: 375
Supero AOC-SIMLC User Manual preview
AOC-SIMLC
Brand: Supero Pages: 68
TP-Link ER8411 Installation Manual preview
ER8411
Brand: TP-Link Pages: 2
3Ware 9550SX Series Installation Manual preview
9550SX Series
Brand: 3Ware Pages: 4
Buffalo LinkStation Quick Setup Manual preview
LinkStation
Brand: Buffalo Pages: 2
ANTAIRA LMP-1202M-SFP Series Quick Installation Manual preview
LMP-1202M-SFP Series
Brand: ANTAIRA Pages: 2
Trend Micro IPS Pro-Module-24C-GE-BP-TM Quick Setup Manual preview
IPS Pro-Module-24C-GE-BP-TM
Brand: Trend Micro Pages: 3
Comet Labs GS8+ User Manual preview
GS8+
Brand: Comet Labs Pages: 11
Idis DR-1204P Installation Manual preview
DR-1204P
Brand: Idis Pages: 22
iGateWeb.com iGate User Manual preview
iGate
Brand: iGateWeb.com Pages: 6
Axis P3365-V Installation Manual preview
P3365-V
Brand: Axis Pages: 98
Compal KALA0 Schematics Document preview
KALA0
Brand: Compal Pages: 47
Microcomputer Systems MSI-P602 User Manual preview
MSI-P602
Brand: Microcomputer Systems Pages: 21

Brands by name

Popular brands

Load more brands