Huawei SmartAX MA5616 Configuration Manual Download

Page: 4 / 553

Symbol

Description

Indicates a tip that may help you solve a problem or save
your time.

Provides additional information to emphasize or
supplement important points of the main text.

Command Conventions

Convention

Description

Boldface

The keywords of a command line are in

boldface

Italic

Command arguments are in

italics

[ ]

Items (keywords or arguments) in square brackets [ ] are
optional.

{ x | y | ... }

Alternative items are grouped in braces and separated by
vertical bars. One is selected.

[ x | y | ... ]

Optional alternative items are grouped in square brackets
and separated by vertical bars. One or none is selected.

{ x | y | ... } *

Alternative items are grouped in braces and separated by
vertical bars. A minimum of one or a maximum of all can
be selected.

GUI Conventions

Convention

Description

Boldface

Buttons, menus, parameters, tabs, window, and dialog titles
are in

boldface

. For example, click

Multi-level menus are in

boldface

and separated by the “>”

signs. For example, choose

File

Create

Folder

Updates in Issue 04 (2011-10-30)

Compared with issue 03 (2011-03-31) of V800R308C01, 04 (2011-10-30) has the following
changes:

Added:

3.3.3 Configuring the System Energy-Saving Function

The following information is modified:

3.1.4 Configuring Inband Management (GE Upstream)

SmartAX MA5616 Multi-service Access Module
Configuration Guide

About This Document

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

iii

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands

Huawei SmartAX MA5616, Configuration Manual

Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands