Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 58 / 553

background image

Example

To set the password for registering with the OLT through the GPON port, set the lower limit for
the receive optical power of the optical transceiver to 5 dBm and the upper limit for the receive
optical power of the optical transceiver to 50 dBm, set the working mode of the optical
transceiver of the upstream PON port to

auto

, do as follows:

huawei(config-if-gponnni-0/0/1)#

password

{ passwordvalue<S><Length 1-10> }:

huawei

Command:
password huawei
huawei(config-if-gponnni-0/0/1)#

optical-module threshold rx-power lower-limit 5

upper-limit 50

{ <cr>|bias<K>|temperature<K>|tx-power<K>|voltage<K> }:

Command:
optical-module threshold rx-power lower-limit 5 upper-limit 50
huawei(config-if-gponnni-0/0/1)#

laser auto

3.3.3 Configuring the System Energy-Saving Function

This topic describes how to power off an unnecessary board to reduce power consumption and
save system energy.

Prerequisites

The board supports power-off and energy-saving modes.

Context

The MA5616 supports manual energy-saving mode. Manual energy-saving allows you to power
off a board manually. Specifically, you can manually power off a board that is not used according
to data plan to reduce energy consumption. When you are about to provision a service on a board
that is manually powered off, the system displays a message indicating that the board is powered
off. In this case, power on the board manually. By default, the energy-saving mode is disabled.

Procedure

l

Run the

board power-off

command to manually power off a board.

–

When a board is not configured with any service, manually power off the board to reduce
energy consumption.

–

After a board is power off manually, run the

board power-on

command to power on

the board.

CAUTION

Exercise caution when running this command because this command will interrupt services
on a board.

l

Run the

broad-service power-off shutdown

command to disable bandwidth services.

–

When an AC-powered device is powered off and is powered by a battery, disable
bandwidth services so that narrowband services can be used for a long time.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

47

«
...
56
57
58
59
60
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: D-Link Pages: 2

Brand: Datasat Pages: 32

S5500-HI Switch Series

Brand: H3C Pages: 180

Brand: H3C Pages: 84

Brand: H3C Pages: 281

Brand: H3C Pages: 8

Brand: H3C Pages: 9

Brand: H3C Pages: 33

Brand: H3C Pages: 42

Brand: H3C Pages: 102

S12500CR Series

Brand: H3C Pages: 9

Brand: H3C Pages: 15

H3C S7500E Series

Brand: H3C Pages: 1565

Brand: H3C Pages: 4

Brand: Fostex Pages: 20

Fieldpoint cFP-RTD-124

Brand: National Instruments Pages: 15

Brand: WAGO Pages: 48

Brand: ICP Pages: 142

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands