Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 208 / 553

background image

The MA5616 can report the multicast log to the log server in syslog mode or in call detailed
record (CDR) mode. By default, the MA5616 reports the log in syslog mode.

l

syslog mode: Logs are reported to the syslog server in the form of a single log.

l

CDR mode: Logs are reported to the log server in the form of a log file (.cvs). One log file
contains multiple logs.

Procedure

l

Configure the parameters of the multicast log generation function of the MA5616.

1.

Enable the multicast log generation function.

The multicast log involves the multicast log of the multicast VLAN, multicast user,
and multicast program. The system generates logs only when the log functions of all
the multicast VLAN, multicast user, and multicast program are enabled. By default,
the log functions of all the multicast VLAN, multicast user, and multicast program
are enabled.

–

In multicast VLAN mode, run the

igmp log { enable | disable }

command to

configure the status of the log function of the multicast VLAN.

–

In BTV mode, run the

igmp user add service-portindexlog { enable | disable }

command to configure the status of the log function of the multicast user.

–

In multicast VLAN mode, run the

igmp program add ipip-addrlog { enable |

disable }

command to configure the status of the log function of the multicast

program.

2.

Change the interval of automatic log generation.

In BTV mode, run the

igmp proxy log-interval

command to change the interval of

automatic log generation.

NOTE

When the user stays online for a long time, the system generates logs at preset intervals. This prevents
the problem that a log is not generated when the user leaves the multicast group without sending the
leave packet, which can affect the accounting. By default, the interval is two hours.

3.

Change the minimum online duration for generating a valid log.

In BTV mode, run the

igmp proxy recognition-time

command to change the

minimum online duration for generating a valid log. If the user is in a multicast group
(such as to preview a program) for shorter than the preset duration, the user operation
is not regarded as a valid one and a log is not generated. A log is generated only when
a user stays online for longer than the specified duration. By default, the duration is
30s.

l

Configure the multicast log report function in CDR mode.

1.

Configure the multicast log server and the data transmission mode for the multicast
log report in CDR mode.

Run the

file-server auto-backup cdr

command to configure the active and standby

multicast log servers.

2.

Enable the multicast log report function in CDR mode.

In BTV mode, run the

igmp cdr { enable | disable }

command to configure the status

of the multicast log report function in CDR mode.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

6 Configuring the Multicast Service (Multicast VLAN Mode)

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

197

«
...
206
207
208
209
210
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: XMG Pages: 5

Brand: Habitat Pages: 48

Brand: NAD Pages: 2

3CR860-95 - OfficeConnect Secure Router

Brand: 3Com Pages: 2

Brand: 3Com Pages: 26

Fast SwitchHub-8mi SNMP

Brand: Accton Technology Pages: 13

Brand: Cypress Semiconductor Pages: 10

Barricade SMC7901WBRA2

Brand: SMC Networks Pages: 2

IPAM-1600s Series

Brand: C-Com Pages: 148

Speed Touch 591s

Brand: Alcatel Pages: 184

Turbo NAS TVS-71 Series

Brand: QNAP Pages: 51

Brand: Longshine Pages: 35

Brand: ICP DAS USA Pages: 8

Brand: Penguin Edge Pages: 2

Brand: SIIG Pages: 8

Brand: Comtrend Corporation Pages: 208

Brand: Dynamix Pages: 87

Brand: FDI Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands