Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 210 / 553

background image

Auto create log interval(h) : 2
Uplink port mode : default
Bandwidth management switch : enable
CDR auto report interval(s) : 600
CDR auto report number : 200
  CDR switch                            : enable  //

The multicast log report in CDR

mode is enabled.

IGMP Packet encapsulation : all
IGMP ECHO switch : disable
Router IP : 192.168.1.1
Initial unsolicited report interval(s): 1
Query offline user switch : -
BTV Forward Mode : Mvlan
----------------------------------------------------------------------

6.3 Configuring the Multicast Service on a Subtending
Network

This topic describes how to configure the multicast service on the MA5616 on a subtending
network.

Prerequisites

l

Network devices and lines must be in the normal state.

l

The multicast source must exist on the network and the IP address of the multicast source
must be known.

Context

When a subtended device needs to provide the multicast service, the subtending port on the
subtending device needs to be configured as the multicast subtending port. In this manner, the
subtended device regards the subtending device as an IGMP user.

Networking

shows the example network of the multicast service in subtending networking mode.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

6 Configuring the Multicast Service (Multicast VLAN Mode)

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

199

«
...
208
209
210
211
212
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: ZETR Pages: 2

Brand: CallDirect Pages: 33

Brand: Panasonic Pages: 4

Brand: CAME Pages: 19

Brand: H3C Pages: 33

S5500-SI Series

Brand: H3C Pages: 1217

Brand: 3Com Pages: 2443

Brand: H3C Pages: 3

Brand: H3C Pages: 4

Brand: T&D Pages: 122

Brand: ekwb Pages: 2

F-Tile SDI II Intel Agilex

Brand: Intel Pages: 39

Brand: Grundig Pages: 24

Brand: Avaya Pages: 73

Brand: BinTec Pages: 34

Brand: Loopcomm Pages: 2

Brand: TP-Link Pages: 2

Brand: Lattice Semiconductor Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands