Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 536 / 553

background image

After an ONU is added, run the

display ont info

command to query the current status

of the ONU. Ensure that

Control flag

of the ONU is

active

,

Run State

is

online

, and

Config state

is

normal

.

huawei(config-if-gpon-0/2)#

display ont info 1 1

---------------------------------------------------------------------

F/S/P :
0/2/1
ONT-ID :
1
Control flag :

active

//Indicates that the ONU is

activated.
Run state :

online

//Indicates that the ONU already goes

online normally.
Config state :

normal

//Indicates that the configuration status

of the ONU is normal.

...//The rest of the response information is omitted.

If the ONU state fails, the ONU fails to be in the up state, or the ONU does not match,
refer to the following suggestions to rectify the fault.

–

If

Control flag

is

deactive

, run the

ont activate

command in the GPON port mode

to activate the ONU.

–

If the ONU fails to be in the up state, that is,

Run state

is

offline

, the physical line

may be broken or the optical transceiver may be damaged. You need to check both
the material and the line.

–

If the ONU state fails, that is,

Config state

is

failed

, the ONU capability set

outmatches the actual ONU capabilities. In this case, run the

display ont failed-

configuration

command in the diagnosis mode to check the failed configuration

item and the failure cause. Then, rectify the fault according to actual conditions.

NOTE

If an ONT supports only four queues, the values of 4-7 of the priority-queue parameter in the

gem add

command are invalid. After configuration recovers, Config state will be failed.

6.

Configure the management channel from the OLT to the ONU.

a.

Configure the inband management VLAN and IP address of the OLT.
To telnet to the ONU from the OLT and then configure the ONU, you need to
configure the inband management VLANs and IP addresses of the OLT and the
ONU on the OLT.
Create management VLAN 8, and configure the inband management IP address
to 192.168.50.1/24.

huawei(config)#

vlan 8 smart

huawei(config)#

interface vlanif 8

huawei(config-if-vlanif8)#

ip address 192.168.50.1 24

huawei(config-if-vlanif8)#

quit

b.

Configure the inband management VLAN and IP address of the ONU.
Configure the static IP address of the ONU 1 to 192.168.50.2/24, the static IP
address of the ONU 2 to 192.168.50.3/24 , the gateway to 192.168.50.254 and
the management VLAN ID to 8 (the same as that of the OLT) .

huawei(config-if-gpon-0/2)#

ont ipconfig 1 1 static ip-address

192.168.50.2
mask 255.255.255.0 gateway 192.168.50.254 vlan 8

huawei(config-if-gpon-0/2)#

ont ipconfig 1 2 static ip-address

192.168.50.3

SmartAX MA5616 Multi-service Access Module
Configuration Guide

10 Configuration Examples of the FTTx

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

525

«
...
534
535
536
537
538
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Farallon Pages: 26

Brand: Observint Pages: 11

Brand: Patton electronics Pages: 8

Brand: Patton electronics Pages: 2

Brand: Patton electronics Pages: 16

Brand: Patton electronics Pages: 51

Brand: Zhone Pages: 7

Brand: Zhone Pages: 1

Brand: iDirect Pages: 52

Brand: Ruckus Wireless Pages: 102

Brand: Belkin Pages: 72

Brand: Helmholz Pages: 28

Brand: process-informatik Pages: 8

Brand: N.A.T. Pages: 32

Brand: peplink Pages: 2

System Storage DS3200

Brand: IBM Pages: 2

D-NVR4108HS-4KS2/L

Brand: Dahua Pages: 33

Brand: AMX Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands