manualshive.com logo in svg

Huawei SmartAX MA5616, Configuration Manual

The Huawei SmartAX MA5616 Configuration Manual is a detailed and comprehensive guide that enables users to efficiently set up and optimize their Huawei SmartAX MA5616. Easily downloadable for free from manualshive.com, this manual provides step-by-step instructions and essential information to maximize your product experience.

Share
Download
background image

Example

Assume that the link set ID is 0, working mode of the link set is active/standby mode, pending
duration is 20s, prefix of the IID is b/, IID generation mode is using the binary value that is
automatically generated in ffsspp mode, namely, parameter 2. To add such an IUA link set, do
as follows:

huawei(config)#

sigtran

huawei(config-sigtran)#

iua-linkset add 0 trafficmode override pendingtime 20 iid-

map 2 
braprefix b/

huawei(config-sigtran)#

display iua-linkset attribute

{ <cr>|linksetno<L> }:                                                          
                                                                                
  Command:                                                                      
          display iua-linkset attribute                                         
----------------------------------------------------------                      
  LinksetNo             :0                                                      
  MGID                  :-                                                      
  PendingTime           :20                                                     
  TrafficMode           :override                                               
  C/S-Mode              :server                                                 
  IID-Type              :integer                                                
  IID-Map               :2                                                      
  BRA IID-Prefix        :b/
  BRA IID-Suffix        :-
  PRA IID-Prefix        :-
  PRA IID-Suffix        :-
  Jointly-Work          :disable                                                
----------------------------------------------------------   

7.3.2.2 Adding an IUA Link

This topic describes how to add an IUA link. After the link set is added, you can add an IUA
link to carry the Q.931 call signaling for the ISDN user.

Prerequisites

The IUA link set must be added.

Context

l

Make sure that a minimum of one item in the local port ID, local IP address, remote port
ID, and remote IP address of a link is different from the corresponding item of other links.

l

Only two links can be configured in the same link set. In addition, the local IP addresses
of the two links must be the same.

Procedure

Step 1

(This step is not required if the command line interface is already in the Sigtran mode.) In global
config mode, run the 

sigtran

 command to enter the Sigtran mode.

Step 2

Run the 

iua-link add

 command to add an IUA link.

Step 3

You can run the 

display iua-link attribute

 command to check whether the configured IUA link

information is the same as the data plan.

----End

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

290

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

D-Link NetDefend DFL-260E Reference Manual preview
NetDefend DFL-260E
Brand: D-Link Pages: 328
D-Link ShareCenter Pulse DNS-320 Quick Install Manual preview
ShareCenter Pulse DNS-320
Brand: D-Link Pages: 2
D-Link DFL-210 - NetDefend - Security Appliance Firewall Registration Manual preview
DFL-210 - NetDefend - Security Appliance
Brand: D-Link Pages: 19
D-Link DFL-M510 Faq preview
DFL-M510
Brand: D-Link Pages: 22
D-Link DFE-680TX Quick Install Manual preview
DFE-680TX
Brand: D-Link Pages: 4
Dahua N300 Quick Start Manual preview
N300
Brand: Dahua Pages: 12
D-Link NetDefend DFL-1600 Quick Manual preview
NetDefend DFL-1600
Brand: D-Link Pages: 23
D-Link Verizon DSL-2750B Setup Manual preview
Verizon DSL-2750B
Brand: D-Link Pages: 6
D-Link DIR-857 Quick Installation Manual preview
DIR-857
Brand: D-Link Pages: 10
D-Link DSL-2740U Quick Installation Manual preview
DSL-2740U
Brand: D-Link Pages: 38
XMG OASIS Disassembly Procedure preview
OASIS
Brand: XMG Pages: 5
Habitat M10 Installation Manual preview
M10
Brand: Habitat Pages: 48
NAD M10 Quick Setup Manual preview
M10
Brand: NAD Pages: 2
3Com IntelliJack NJ200 Datasheet preview
IntelliJack NJ200
Brand: 3Com Pages: 4
Yamaha EMP100 Supplementary Manual preview
EMP100
Brand: Yamaha Pages: 4
JB Systems Scene Master Operation Manual preview
Scene Master
Brand: JB Systems Pages: 24
JB Systems CMX 24 User Manual preview
CMX 24
Brand: JB Systems Pages: 61
Commell ES-270 User Manual preview
ES-270
Brand: Commell Pages: 36

Brands by name

Popular brands

Load more brands