Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 390 / 553

background image

Item

Data

Upstream
priority

The 802.1p priorities are used. The VoIP service has priority 6, IPTV service
priority 5, and Internet service priority 1.

Configuration Flowchart

Figure 8-13

shows the flowchart for configuring the triple play service based on the user-side

VLAN.

Figure 8-13

Flowchart for configuring the triple play service based on the user-side VLAN

Procedure

l

Configure the Internet service.
1.

Create a VLAN and add an uplink port to the VLAN.

huawei(config)#

vlan 102 smart

huawei(config)#

port vlan 102 0/0 1

2.

Configure a traffic profile.

–

Because the VoIP, IPTV, and Internet services are provided through the same port,
you must set the 802.1p priority of each service.

–

Generally, the priorities are in a descending order for the VoIP service, IPTV
service, and Internet service. In this example, set the traffic profile index to 7 and
the 802.1p priority of the Internet service to 1.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

379

«
...
388
389
390
391
392
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

NetDefend DFL-260E

Brand: D-Link Pages: 328

ShareCenter Pulse DNS-320

Brand: D-Link Pages: 2

DFL-210 - NetDefend - Security Appliance

Brand: D-Link Pages: 19

Brand: D-Link Pages: 22

Brand: D-Link Pages: 4

Brand: Dahua Pages: 12

NetDefend DFL-1600

Brand: D-Link Pages: 23

Brand: D-Linke Pages: 32

Brand: Lattice Semiconductor Pages: 15

iCE40 UltraLite

Brand: Lattice Semiconductor Pages: 13

Brand: TC-Helicon Pages: 2

Brand: Accuphase Pages: 2

Brand: ADTRAN Pages: 2

AMB-VDX3H1 Series

Brand: Acrosser Technology Pages: 4

Brand: Lanner Pages: 2

Brand: APARIAN Pages: 2

Brand: IEI Technology Pages: 86

Lite N42B1P Series

Brand: Dahua Technology Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands