Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 419 / 553

background image

NOTE

By default, an SHDSL port is in the activated state. Before binding a profile or template to the port, you
must deactivate the port.

huawei(config)#

interface shl 0/4

huawei(config-if-shl-0/4)#

deactivate 0

huawei(config-if-shl-0/4)#

activate 0 3

huawei(config-if-shl-0/4)#

alarm-config 0 1

huawei(config-if-shl-0/4)#

quit

3.

Run the

display traffic table

command to query the existing traffic profiles in the system.

huawei(config)#

display traffic table ip from-index

0

{ <cr>|to-
index<K> }:


Command:
display traffic table ip from-index
0

----------------------------------------------------------------------------
TID CIR(kbps) CBS(bytes) PIR(kbps) PBS(bytes) Pri Copy-policy Pri-
Policy

----------------------------------------------------------------------------
0 1024 34768 2048 69536 6 - tag-
pri
1 2496 81872 4992 163744 6 - tag-
pri
2 512 18384 1024 36768 0 - tag-
pri
3 576 20432 1152 40864 2 - tag-
pri
4 64 4048 128 8096 4 - tag-
pri
5 2048 67536 4096 135072 0 - tag-
pri
6 off off off off 0 - tag-
pri

----------------------------------------------------------------------------
Total Num : 7

According to service requirements, the user access rate is 2048 kbit/s. The query result
shows that traffic profile 5 (for inbound and outbound rate limitation) meets the
requirements.

NOTE

l

If a matched traffic profile is not available in the system, run the

traffic table ip

command to configure

a new traffic profile.

l

On the MA5616, the user access rate can be limited by either a traffic profile or an SHDSL line profile.
When both profiles are configured, the smaller one of the two rates configured in the profiles is adopted
as the user bandwidth. In this example, the traffic profile is used to limit the user access rate.

4.

Run the

service-port

command to create a service port, adopt traffic profile 5, and set the

S-VLAN ID to 50. Set the SHDSL channel mode to PTM, and create service port 2 on
SHDSL port 0/4/0. To facilitate the maintenance of the service port, also configure the
service port description.

huawei(config)#

service-port 2 vlan 50 shdsl mode ptm 0/4/0 inbound traffic-

table index 5 outbound traffic-table index 5

huawei(config)#

service-port desc 2 description Vlanid:50/shdsl/vpi:1vci:39/

stacking

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

408

«
...
417
418
419
420
421
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

UR5i v2 Libratum

Brand: B+B SmartWorx Pages: 8

Brand: B+B SmartWorx Pages: 8

Brand: ICP DAS USA Pages: 14

Brand: ICP DAS USA Pages: 25

Brand: ICP DAS USA Pages: 15

Brand: ICP DAS USA Pages: 8

Brand: ICP Pages: 14

Brand: Zenith Data Systems Pages: 64

Brand: IEI Technology Pages: 3

Brand: LevelOne Pages: 31

Brand: ROE Pages: 41

Millennium P650

Brand: Matrox Pages: 54

NIC-FC730i-Mb-2-32G

Brand: H3C Pages: 37

Brand: axing Pages: 4

Brand: eWON Pages: 34

OptiBond 210 C Series

Brand: i-MO Pages: 16

PacketMate 1000

Brand: General DataComm Pages: 20

Brand: Comtrend Corporation Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands