Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 120 / 553

background image

Create HWTACACS server template named

test-login

with HWTACACS server 129.7.66.66

as the primary authentication server, and HWTACACS server 129.7.66.67 as the secondary
authentication server.

huawei(config)#

hwtacacs-server template test-login

Create a new HWTACACS-server template
huawei(config-hwtacacs-test-login)#

hwtacacs-server authentication 129.7.66.66 1812

huawei(config-hwtacacs-test-login)#

hwtacacs-server authentication 129.7.66.67 1812

secondary

huawei(config-hwtacacs-test-login)#

quit

Step 3

Create a domain named

isp1

.

NOTE

l

A domain is a group of users of the same type.

l

When the user name is in the format of

userid@domain-name

(for example,

[email protected]

), "domain-name" followed by "@" is the domain name, and "userid" is

the user name used for authentication.

l

The common domain name for login cannot exceed 15 characters, and the domain name for 802.1x
authentication cannot exceed 20 characters.

huawei(config)#

aaa

huawei(config-aaa)#

domain isp1

Info: Create a new domain

Step 4

Use the authentication scheme

login-auth

.

You can use an authentication scheme in a domain only after the authentication scheme is
created.

huawei(config-aaa-domain-isp1)#

authentication-scheme login-auth

Step 5

Bind the HWTACACS server template

test-login

to the user.

You can use a HWTACACS server template in a domain only after the HWTACACS server
template is created.

huawei(config-aaa-domain-isp1)#

hwtacacs-server test-login

Step 6

Configure the authentication mode of the management user.
In the global config mode, run the

terminal user authentication-mode

command to configure

the authentication of the management user to remote AAA.

NOTE

l

Only the

root

user can run this command.

l

After the authentication of the management user is configured to remote AAA, the system prefers
RADIUS authentication (the

root

user is still forcible local authentication).

huawei(config)#

terminal user authentication-mode aaa isp1

Step 7

(Optional) Configure the local management user of the device.

If the HWTACACS server is unreachable, local authentication can be used to log in to the system.
If the HWTACACS server is reachable, none of the management users can log in to the system
through local authentication, except the

root

user.

CAUTION

Ensure that the user name and password of the local management user are the same as those
specified on the HWTACACS server. Otherwise, login to the system fails.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

109

«
...
118
119
120
121
122
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

C50FSi - VB Network Camera

Brand: Canon Pages: 32

Brand: Rabbit Pages: 120

UR5i v2 Libratum

Brand: B+B SmartWorx Pages: 8

Brand: B+B SmartWorx Pages: 8

Brand: Lanpro Pages: 5

Brand: SAF Pages: 30

Brand: VMIC Pages: 126

EXPANSION CARD X-DANTE

Brand: Behringer Pages: 65

Brand: Zoom Pages: 88

Brand: SyChip Pages: 24

Brand: Conel Pages: 32

Brand: SSV Embedded Systems Pages: 17

LMP-1202M-SFP Series

Brand: ANTAIRA Pages: 2

Brand: Paradyne Pages: 74

Brand: ZyXEL Communications Pages: 348

N-FXE 02B Series

Brand: Lantronix Pages: 10

Imagestore Intuition+

Brand: Miranda Pages: 60

Brand: Matrix Switch Corporation Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands