Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 443 / 553

background image

Device

Item

Data

Program
library

Program in multicast VLAN 4002:
Program 1: with IP address 224.1.1.1 and the IP address
of the program source is the same as the IP address of ISP
1, namely, 10.10.10.10

Program in multicast VLAN 4003:
Program 2: with IP address 224.1.1.2 and the IP address
of the program source is the same as the IP address of ISP
2, namely, 10.10.10.11

Multicast user

Multicast user 1:

l

VDSL2 port: 0/1/0

l

LAN port: 0/3/1

l

Multicast VLAN: 4002

Multicast user 2:

l

VDSL2 port: 0/1/1

l

LAN port: 0/3/2

l

Multicast VLAN: 4003

Procedure

Step 1

Create VLANs and add an uplink port to the VLANs.

huawei(config)#

vlan 4002-4005 smart

huawei(config)#

port vlan 4002-4005 0/0 1

Step 2

Configure service ports.

huawei(config)#

service-port 100 vlan 4004 vdsl mode ptm 0/1/0 multi-service user-

vlan untagged
rx-cttr 6 tx-cttr 6

huawei(config)#

service-port 101 vlan 4005 vdsl mode ptm 0/1/1 multi-service user-

vlan untagged
rx-cttr 6 tx-cttr 6

Step 3

Configure multicast VLANs and the multicast mode.

NOTE

The IGMP mode can be configured to IGMP proxy or IGMP snooping according to the requirements. In
this example, the IGMP mode is IGMP proxy. If the planned IGMP mode is IGMP snooping, you can
configure the IGMP snooping mode by running the

igmp mode snooping

command in multicast VLAN

mode.

The IGMP mode can be switched only when the IGMP mode is off.

huawei(config)#

multicast-vlan 4002

huawei(config-mvlan4002)#

igmp mode proxy

Are you sure to change IGMP mode?(y/n)[n]:

y

huawei(config-mvlan4002)#

multicast-vlan 4003

huawei(config-mvlan4003)#

igmp mode proxy

Are you sure to change IGMP mode?(y/n)[n]:

y

Step 4

Configure the multicast uplink port.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

432

«
...
441
442
443
444
445
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: D-Linke Pages: 32

Brand: GE Pages: 146

Netlink FRX8000

Brand: Cabletron Systems Pages: 94

MMAC-Plus 9E423-24

Brand: Cabletron Systems Pages: 10

MMAC-Plus 9A128-01

Brand: Cabletron Systems Pages: 22

Spectrum EMM-E6

Brand: Cabletron Systems Pages: 2

SmartSTACK ELS100-24TXG

Brand: Cabletron Systems Pages: 112

Brand: Cabletron Systems Pages: 86

Brand: Cabletron Systems Pages: 54

Cabletron BRIM-F6

Brand: Cabletron Systems Pages: 43

Netlink FRX4000

Brand: Cabletron Systems Pages: 60

CSX200 CyberSWITCH

Brand: Cabletron Systems Pages: 2

Brand: Cabletron Systems Pages: 8

Brand: Cabletron Systems Pages: 4

Brand: Watchguard Pages: 39

ACC-CX3RDK-CU5640

Brand: e-con Systems Pages: 9

Emulator MCU Board for 38D5 Group M38D59T-RLFS

Brand: Renesas Pages: 4

BIC 1I12-P2A25-M30MI1-BPX05-110

Brand: Balluff Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands