manualshive.com logo in svg

Huawei SmartAX MA5616, Configuration Manual

The Huawei SmartAX MA5616 Configuration Manual is a detailed and comprehensive guide that enables users to efficiently set up and optimize their Huawei SmartAX MA5616. Easily downloadable for free from manualshive.com, this manual provides step-by-step instructions and essential information to maximize your product experience.

Share
Download
background image

Item

Data

Remarks

Analog parameter ID: 2

The user-defined humidity monitoring analog
parameter is added to monitor the ambient
humidity of the device.
For values and details of this parameter, see the

esc analog

 command.

Upper alarm threshold of
analog parameter 2: 75%
RH

When the ambient humidity of the device is
higher than 75% RH, the device reports an alarm.

Lower alarm threshold of
analog parameter 2: 5%
RH

When the ambient humidity of the device is
lower than 5% RH, the device reports an alarm.

Name of analog parameter
2: humidity

-

Alarm ID of analog
parameter 2: 2

The user-defined humidity alarm of the system
is used.

Unit of analog parameter
2: % RH

-

Sensor type of analog
parameter 2: voltage type

-

Digital
parameters

Digital parameter ID: 1

This parameter is invariably allocated by the
system, and is used to monitor the door status of
the telecommunications room. You cannot
modify any parameter of this digital parameter,
except the valid level.

Valid level of digital
parameter 1: high level

When the high level represents the valid level,
the device does not report an alarm in the case of
high level.

Digital parameter ID: 2

-

Valid level of digital
parameter 2: low level

When the low level represents the valid level, the
device does not report an alarm in the case of low
level.

Name of digital parameter
2: Fan

It is a user-defined digital parameter and is set
according to the actual requirements. The
monitoring digital parameter of the fan unit is set
here to monitor the fan unit.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

137

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

YASKAWA SI-EP3/V Installation Manual preview
SI-EP3/V
Brand: YASKAWA Pages: 68
hawa HAWA-Frontside 60/B Planning And Installation Instructions preview
HAWA-Frontside 60/B
Brand: hawa Pages: 28
QNO 2WAN 3LAN User Manual preview
2WAN 3LAN
Brand: QNO Pages: 106
Face XR18 User Manual preview
XR18
Brand: Face Pages: 8
BSS Audio EC-4B Installation Manual preview
EC-4B
Brand: BSS Audio Pages: 20
Reeven NAIA Installation Manual preview
NAIA
Brand: Reeven Pages: 2
ADC HiGain HLU-231 List 8F Quick Installation preview
HiGain HLU-231 List 8F
Brand: ADC Pages: 7
Dialogic EDP-10 Quick Install Manual preview
EDP-10
Brand: Dialogic Pages: 2
FS FS-BOX-V3 Quick Start Manual preview
FS-BOX-V3
Brand: FS Pages: 19
Aruba IntroSpect Analyzer 2 Series Quick Start Manual preview
IntroSpect Analyzer 2 Series
Brand: Aruba Pages: 5
M86 Security M86 Web Filter User Manual preview
M86 Web Filter
Brand: M86 Security Pages: 309
TP-Link TL-SG2424P User Manual preview
TL-SG2424P
Brand: TP-Link Pages: 176
Solwise WLn-401 Quick Installation Manual preview
WLn-401
Brand: Solwise Pages: 7
Advantech 3718HG User Manual preview
3718HG
Brand: Advantech Pages: 68
Hauppauge WinTV-DVB Installation And Reference Manual preview
WinTV-DVB
Brand: Hauppauge Pages: 62
Intel 500 - DATASHEET REV 003 Datasheet preview
500 - DATASHEET REV 003
Brand: Intel Pages: 67
TP-Link Deco XE200 User Manual preview
Deco XE200
Brand: TP-Link Pages: 57
Waver WAC52N Quick Start Manual preview
WAC52N
Brand: Waver Pages: 36

Brands by name

Popular brands

Load more brands