Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 284 / 553

background image

Parameter

Remarks

transfer

The transmission mode is selected according
to the requirements of the MGC. Generally,
UDP is used.

start-negotiate-version

If the MGC connecting to the MG is a Huawei
device, the profile (parameter profile-index)
does not need to be set; if the MGC
connecting to the MG is a device of another
vendor, the profile (parameter profile-index)
must be set (the parameter value is prompted
on the CLI).
If the profile file in the system cannot meet
requirements, contact Huawei for technical
support.

Step 3

Check whether the attribute of the MG interface is the same as that in the data plan.

Run the

display if-h248 attribute

command to check whether the attribute of the MG interface

is the same as that in the data plan.

----End

Example

Assume that the MG interface ID is 0, the H.248 protocol is used for interconnecting with the
MGC, the signaling IP address is 10.13.4.116, the transport layer protocol port ID is 2944, IP
address 1 of the primary MGC is 10.13.2.118, the transport layer protocol port ID of the primary
MGC is 2944, media IP address 1 is 10.71.46.69, media IP address 2 is 10.13.4.117, the H.248
protocol version is started to be negotiated based on the profile, the transaction reliability is
enabled. To add such an MG interface, do as follows:

huawei(config)#

interface h248 0

Are you sure to add MG interface?(y/n)[n]:

y

huawei(config-if-h248-0)#

if-h248 attribute mgip 10.13.4.116 mgport 2944 code text

primary-mgc-ip1 10.13.2.118 primary-mgc-port 2944 mg-media-ip1 10.71.46.69
mg-media-ip2 10.13.4.117 start-negotiate-version 0 retrans enable

huawei(config-if-h248-0)#

display if-h248 attribute

-------------------------------------------------
MGID 0
MG Description -
MG DomainName -
Protocol H248
Start Negotiate Version 0
Profile Negotiation Parameter Disable
Profile index 1:NoProfile("")
2833Encrypt -
Codetype Text
Transfer Mode -
HeartBeatGenTimer(s) 60
HeartBeatRetransTimes 3
HeartBeatRetransTimer(s) 60
MG signalling IP 10.13.4.116
MG signalling Port 2944
MG media IP1 10.71.46.69
MG media IP2 10.13.4.117
MIDType IP4_ADDR
DeviceName -

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

273

«
...
282
283
284
285
286
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: LAWO Pages: 154

Brand: Zonet Pages: 8

AirPlus XtremeG Ethernet-to-Wireless Bridge...

Brand: D-Link Pages: 31

HAWA-Frontside 60/B

Brand: hawa Pages: 28

NJ220 - IntelliJack Switch

Brand: 3Com Pages: 82

Conel UR5i v2 Libratum

Brand: B&B Electronics Pages: 32

Brand: NEC Pages: 2

Parallel Printer Card PIOC

Brand: B&B Electronics Pages: 16

F-Tile SDI II Intel Agilex

Brand: Intel Pages: 39

AyrMesh IndoorAP

Brand: AYRSTONE Pages: 2

Brand: Netis Pages: 16

Brand: IEI Technology Pages: 3

Brand: Eneo Pages: 68

Brand: Techroutes Pages: 20

Brand: JUMO Pages: 60

Brand: iGateWeb.com Pages: 6

Brand: Axis Pages: 98

CNPS5X PERFORMA

Brand: ZALMAN Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands