Huawei SmartAX MA5616 Configuration Manual Download

Page: 502 / 553

Servic
e
Classif
ication

Item

Data

Remarks

User priorities:
Phone 1: Cat2;
Phone 2-Phone 24:
Cat3 (default)

According to the service requirements, user
priorities must be specified. The user
priorities include the following:

cat1: government1 (category 1
government users)

cat2: government2 (category 2
government users)

cat3: common (common users)

Emulati
on
service
data

Local LSR
ID

10.10.10.10/32

Generally, the IP address of the loopback
interface is used as the LSR ID.

Remote
(OLT) LSR
ID

10.20.20.20/32

Remote
(PTN) LSR
ID

30.30.30.30/32

10.3 Configuring Upstream Link Aggregation

Configure the upstream link aggregation group to improve the bandwidth and reliability of the
upstream link of the OLT.

Service Requirements

The bandwidth of a single upstream port of the OLT is insufficient and two upstream ports
are required.

Two upstream ports of the OLT provide load balancing function.

Two upstream ports of the OLT back up each other. When one port is faulty, the other port
ensures the normal forwarding of the service.

Table 10-3

Data plan

Item

Data

Upstream ports

0/19/0 and 0/19/1

Aggregation group

Packet allocation mode: according to the source MAC
address
Working mode: lacp-static

SmartAX MA5616 Multi-service Access Module
Configuration Guide

10 Configuration Examples of the FTTx

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

491

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands

Huawei SmartAX MA5616, Configuration Manual

Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands