Huawei SmartAX MA5616 Configuration Manual Download

Page: 140 / 553

Context

The traffic priority is only valid to permit rules of an ACL.

Procedure

Step 1

Run the

traffic-priority

command to add a priority tag to the traffic matching an ACL rule on

a specified port.

Step 2

Run the

display qos-info traffic-priority port

command to query the configured priority.

----End

Example

To add a priority tag to the traffic that matches ACL 2001 received on port 0/2/0, and the local
priority of the traffic is 0 , do as follows:

huawei(config)#

traffic-priority inbound ip-group 2001 local-precedence 0 port 0/2/0

huawei(config)#

display qos-info traffic-priority port 0/2/0

traffic-priority:
port 0/2/0:
Inbound:
Matches: Acl 2001 rule 5 running
Priority action: local-precedence 0

3.14.3.3 Enabling the Statistics Collection of the Traffic Matching an ACL Rule

This topic describes how to enable the statistics collection of the traffic matching an ACL rule,
thus analyzing and monitoring the traffic.

Prerequisite

The ACL and the rule of the ACL are configured, and the port for traffic statistics is working in
the normal state.

Context

The traffic statistics are only valid to permit rules of an ACL.

Procedure

Step 1

Run the

traffic-statistic

command to enable the statistics collection of the traffic matching an

ACL rule on a specified port.

Step 2

Run the

display qos-info traffic-mirror port

command to query the statistics information about

the traffic matching an ACL rule on a specified port.

----End

Example

To enable the statistics collection of the traffic that matches ACL 2001 received on port 0/0/1,
do as follows:

huawei(config)#

traffic-statistic inbound ip-group 2001 port 0/0/1

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

129

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands

Huawei SmartAX MA5616, Configuration Manual

Search results

Summary of Contents for SmartAX MA5616

Reviews:

Related manuals for SmartAX MA5616

Brands by name

Popular brands