Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 457 / 553

background image

board, thus implementing the ISDN BRA service. The ISDN BRA service on the MA5616 can
be supported only by the H.248 protocol.

Prerequisites

l

The devices on the network must be connected properly and must work in the normal state.

l

The MA5616 must use the H.248 protocol to communicate with the MGC.

l

The data on the MGC side must be configured correctly.

l

NT1 must be connected properly and must work in the normal state.

Context

l

When the MG interface does not support the terminal layering, the terminal ID must be
configured and must be different from the terminal ID of an existing PSTN user.

l

When the MG interface supports terminal layering, the terminal ID cannot be configured,
and the system automatically allocates the terminal ID according to the TID profile
configured for the interface of the PSTN user.

l

You can run the

display tid-format

to query the TID profile to which various users under

the MG interface are bound, and then run the

display tid-template

command to check

whether the TID profile supports the layering configuration. Hence, you can check whether
the user supports terminal layering.

–

If the parameter list of the TID profile includes only keyword "G", it indicates that the
TID profile is used by the non-layering users. Users bound with this profile do not
support terminal layering.

–

If the parameter list of the TID profile includes only keywords "F", "S", "P", "B" ("B"
is unavailable for PSTN users), it indicates that the TID profile is used by the layering
users. Users bound with this profile support terminal layering.

Networking

shows the example network for configuring the ISDN BRA service.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

446

«
...
455
456
457
458
459
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: D-Link Pages: 99

Brand: D-Link Pages: 5

Brand: D-Link Pages: 15

AirPro DWL-6000AP

Brand: D-Link Pages: 65

Brand: Aztech Pages: 2

Brand: Tripp Lite Pages: 3

Brand: SAGEMCOM Pages: 75

Brand: 3Com Pages: 50

EZ-Extender Analog 120-Pin Probing Board

Brand: Analog Devices Pages: 29

Seven Solutions WR-ZEN Series

Brand: Orolia Pages: 167

InvenSense RoboKit1

Brand: TDK Pages: 13

Brand: Glacier Pages: 2

Brand: Galaxy Pages: 30

ELITENAS EN104L+(B)

Brand: Sans Digital Pages: 9

Brand: Pakedge Device & Software Pages: 14

J-Link-OB-STM32F072-128KB

Brand: Segger Pages: 18

CHEETAH ST34501FC

Brand: Seagate Pages: 68

IE-SW-PL09M-5GC-4GT

Brand: Weidmuller Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands