Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 520 / 553

background image

NOTE

l

The VLAN ID must be consistent with the CVLAN of the OLT.

l

An MA5616 (ONU) provides two upstream ports 0/0/0 and 0/0/1 and supports self-adaptation
among three modes.

huawei(config)#

vlan 1001-1024 smart

huawei(config)#

port vlan 1001-1024 0/0 1

4.

Configure a VDSL2 line profile.

–

Run the

display vdsl line-profile

command to query the existing VDSL2 line

profiles in the current system. A profile can be directly used if it meets the
requirements.

–

If no VDSL2 line profile in the system meets the requirements, you need to add a
VDSL2 line profile. Run the

vdsl line-profile quickadd

command to quickly add

a VDSL2 line profile.

The data in the VDSL2 line profile must be configured according to the actual line
conditions. In this example, quickly add VDSL2 line profile 4 by using default settings
for the parameters.

huawei(config)#

vdsl line-profile quickadd 4

5.

Configure the VDSL2 channel profile.

–

Run the

display vdsl channel-profile

command to query the existing VDSL2

channel profiles in the current system. A profile can be directly used if it meets the
requirements.

–

If no VDSL2 channel profile in the system meets the requirements, you need to
add a VDSL2 channel profile. Run the

vdsl channel-profile quickadd

command

to add a VDSL2 channel profile.

NOTE

The data in the VDSL2 channel profile must be configured according to the actual channel
conditions. In this example, the traffic profile is used to limit the subscriber access rate;
therefore, when the VDSL2 channel profile is configured, the line rate parameters do not need
to be configured.

Quickly add VDSL2 channel profile 4 and use default settings for the parameters.

huawei(config)#

vdsl channel-profile quickadd 4

6.

Configure the VDSL2 line template.

–

Run the

display vdsl line-template

command to query the existing VDSL2 line

templates in the current system. A template can be directly used if it meets the
requirements.

–

If no VDSL2 line template in the system meets the requirements, you need to add
a VDSL2 line template. Run the

vdsl line-template quickadd

command to add a

VDSL2 line template.

Bind the VDSL2 line profile configured in

and the VDSL2 channel profile

configured in

Set the downstream rate adaptation ratio to 100% and the

upstream rate adaptation ratio to 100%.

huawei(config)#

vdsl line-template quickadd 3 line 4 channel1 4 100 100

7.

Activate VDSL2 port 0/1/0 and bind line template 3 to it.

NOTE

The other VDSL2 ports can be activated similarly. If you want to activate all the ports of a board,
use the command

activate all

.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

10 Configuration Examples of the FTTx

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

509

«
...
518
519
520
521
522
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Express EtherNetwork DFE-670TXD

Brand: D-Link Pages: 4

Brand: DAD Pages: 36

Brand: D-Link Pages: 2

Brand: D-Link Pages: 10

Brand: 4IPNET Pages: 97

Brand: Zenith Data Systems Pages: 64

DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network...

Brand: D-Link Pages: 53

Brand: Juniper Pages: 825

Brand: OpenVox Pages: 13

8677 - BladeCenter Rack-mountable - Power Supply

Brand: IBM Pages: 126

Brand: Softing Pages: 4

Brand: ICP DAS USA Pages: 8

Brand: Arbor Technology Pages: 8

Brand: Navitar Pages: 1

Vocal Performer VE-20

Brand: Boss Pages: 20

Brand: DIGIWEB Pages: 16

Brand: Variscite Pages: 17

Brand: Xilinx Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands