Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 327 / 553

background image

MA5616 in the upstream direction. For the identification purpose, the user name and
password for dial-up Internet access must be configured on the BRAS.

Procedure

Step 1

Configure a VLAN.

Configure S-VLAN 50 with the stacking attribute. The user packet goes upstream carrying two
VLAN tags. The outer VLAN tag identifies the service and the inner VLAN tag identifies the
user. The service of each user is identified by unique S-VLAN+C-VLAN, and the VLAN
forwarding mode is the S-VLAN+C-VLAN mode.

huawei(config)#

vlan 50 smart

huawei(config)#

vlan attrib 50 stacking

huawei(config)#

vlan service-profile profile-id 1

huawei(config-vlan-srvprof-1)#

forwarding vlan-connect

huawei(config-vlan-srvprof-1)#

commit

huawei(config-vlan-srvprof-1)#

quit

huawei(config)#

vlan bind service-profile 50 profile-id 1

Step 2

Configure upstream ports.
Add upstream ports 0/0/0 to VLAN 50.

huawei(config)#

port vlan 50 0/0 0

Step 3

In the ADSL access mode, follow this procedure.
1.

Configure an ADSL2+ profile. For details, see

3.7.1 Configuring the ADSL2+ Profile

.

Here, the default ADSL2+ line template (line template 1) and the default ADSL2+ alarm
template (alarm template 1) are used as an example.

2.

Activate the ADSL port, and bind the ADSL2+ templates.

NOTE

By default, an ADSL port is in the activated state. Before binding a template to the port, you must deactivate
the port.

In the ADSL access mode, bind the default ADSL2+ line template 1 and ADSL2+ alarm
template 1 to ADSL port 0/2/0.

huawei(config)#

interface adsl 0/2

huawei(config-if-adsl-0/2)#

deactivate 0

huawei(config-if-adsl-0/2)#

activate 0 template-index 1

huawei(config-if-adsl-0/2)#

alarm-config 0 1

huawei(config-if-adsl-0/2)#

quit

3.

Run the

display traffic table

command to query the existing traffic profiles in the system.

huawei(config)#

display traffic table ip from-index

0

{ <cr>|to-
index<K> }:


Command:
display traffic table ip from-index
0

----------------------------------------------------------------------------
TID CIR(kbps) CBS(bytes) PIR(kbps) PBS(bytes) Pri Copy-policy Pri-
Policy

----------------------------------------------------------------------------
0 1024 34768 2048 69536 6 - tag-
pri
1 2496 81872 4992 163744 6 - tag-
pri

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

316

«
...
325
326
327
328
329
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Idis Pages: 86

Brand: Paradyne Pages: 20

Brand: Paradyne Pages: 2

Brand: Cypress Semiconductor Pages: 9

Brand: Winext Pages: 37

Sentry Global Security Modem

Brand: Server Technology Pages: 22

4-Port 10/100Mbps Ethernet Broadband Router

Brand: AOpen Pages: 41

Brand: Telit Wireless Solutions Pages: 113

Momentum ROG Strix X570-E D-RGB

Brand: EK-Quantum Pages: 10

Brand: UfiSpace Pages: 34

Brand: CELOT Pages: 34

Brand: Compro Technology Pages: 2

Brand: Korenix Pages: 25

Brand: ZiLOG Pages: 317

Brand: Lanner Pages: 141

Brand: Garderos Pages: 21

Brand: CTC Union Pages: 12

SmartNode 4634 Series

Brand: Patton electronics Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands