Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 372 / 553

background image

huawei(config-pstnport)#

pstnport attribute batset 0/3/1 0/3/31 reverse-pole-pulse

enable

Step 4

Save the data.

huawei(config-pstnport)#

quit

huawei(config)#

save

----End

Result

After the configuration, phone 0-phone 31 can call each other.

l

The calling party can hear the dial tone after picking up the phone off the hook.

l

When the calling party dials the phone number of the called party, the phone of the called
party can ring normally, and the calling party can hear the ringback tone.

NOTE

When the calling party calls the number of a specified user, if the phone of the specified user does
not ring but the phone of another user connected to the MA5616 rings, and the calling party hears
the ringback tone, check whether the IMS is configured with the call forwarding service, causing the
line cross.

l

If the IMS is configured with the call forwarding service, cancel the call forwarding service on
the IMS.

l

If the IMS is not configured with the call forwarding service, contact Huawei technical support
engineer to handle the fault.

l

The calling party and the called party can communicate with each other normally.

l

After the called party places the phone on the hook, the calling party can hear the busy tone.

Configuration File

The following part describes the configuration file of this configuration example. Note that
certain steps must be performed manually and the configuration file cannot be imported directly.

Configure the local digitmap.

local-digitmap add huawei0 normal ([2-8]xxxxxxx|[2-8]xxSxxxxxxx|
13xxxxxxxxx|0xxxxxxxxx|9xxxx|1[0124-9]x|F|x.F|[0-9].S)
local-digitmap add huawei1 second-centrex (8100)

Configure the PSTN user data.

esl user
sippstnuser batadd 0/3/0 0/3/31 0 telno 83110000
sippstnuser attribute set 0/3/0 priority cat2
sippstnuser attribute batset 0/3/1 0/3/31 potslinetype PayPhone

Configure the PSTN port attribute.

quit
pstnport
pstnport attribute batset 0/3/1 0/3/31 reverse-pole-pulse enable

Save the data.

quit
save

8.3.3 Configuration Example of the VoIP ISDN BRA Service

When the H.248 protocol is used, the MA5616 can access the ISDN BRA service through the
DSLD service board. Then, the service is sent upstream to the IP network through the control

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

361

«
...
370
371
372
373
374
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: XESS Pages: 23

Brand: LevelOne Pages: 31

Brand: FS Pages: 19

PoleVault System A/V Source Inputs

Brand: Extron electronics Pages: 4

Brand: Renesas Pages: 2

Brand: ebm-papst Pages: 11

COMMWARE ECHO 5G

Brand: pivotal Pages: 2

Enterasys Matrix 2G4082-25

Brand: Enterasys Pages: 58

Brand: Freund Pages: 6

Brand: C&T Solution Pages: 129

Converter Board R0E521237CFK00

Brand: Renesas Pages: 6

Brand: MEDIATEK Pages: 166

Brand: Intel Pages: 958

Vortex86SX VSX-6100

Brand: ICOP Technology Pages: 50

Brand: Matrix Switch Corporation Pages: 60

SFD-2 MkIII Jumper

Brand: Anthem Audio Pages: 2

Brand: Intel Pages: 54

Brand: Nexxt Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands