Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 241 / 553

background image

template that is bound to the type of users. Then, run the

display tid-template

command to

check whether the TID template supports the layering configuration. Hence, you can check
whether the user supports terminal layering.

Precaution

l

There are 19 default TID templates (templates 0-18) in the system. The default TID
templates can be referenced, but cannot be added, modified, or deleted.

l

The configuration of terminal layering on the MG must be the same as that on the MGC.

l

If certain type of terminals exists on an interface and the interface is not disabled, the
terminal prefix of this type of terminals cannot be modified.

l

If a certain type of terminals exists on an interface, the TID format (including the terminal
prefix and the index of the TID template) of this type of terminals cannot be changed.

l

The terminal prefix must comply with the following syntax rules: The prefix must not
exceed 64 characters. Only letters, digits, "_", and "/" are the characters allowed for input.
The first character must be a letter, and the last character must not be a digit.

l

The length of the TID, which is generated by combining the TID template and the terminal
prefix that you configured, must not exceed 64 characters.

Procedure

Step 1

To query the template information.

Run the

display tid-template

command to query the information about the default TID template

of the system.

Step 2

Check whether the default TID template of the system meets the service requirements.

If the default TID template cannot meet the service requirements, run the

tid-template add

command to add a TID template that meets the service requirements. If the default TID template
meets the service requirements, proceed to

Step 3

Enter the MG interface mode.

Run the

interface h248

command to enter the MG interface mode.

Step 4

Configure the TID templates and the terminal prefix of various types of users on the current MG
(VAG).

l

In H248 mode, run the

tid-format rtp

command to configure the TID template and terminal

prefix of the RTP ephemeral termination.

l

In H248 mode, run the

tid-format pstn

command to configure the TID template and terminal

prefix of the PSTN user.

l

In H248 mode, run the

tid-format pstn

command to configure the TID template and the

terminal prefix of the ISDN BRA user.

l

In H248 mode, run the

tid-format pstn

command to configure the TID template and terminal

prefix of the ISDN PRA user.

Step 5

Check whether the TID template and the terminal prefix are the same as those in the data plan.

Run the

display tid-format

command to check whether the TID templates and the terminal

prefixes of various types of users on the current MG interface are the same as those in the data
plan.

----End

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

230

«
...
239
240
241
242
243
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: D-Linke Pages: 32

UP Squared 6000 Edge Computing Kit

Brand: Aaeon Pages: 59

Brand: EAW Pages: 6

Brand: EAW Pages: 6

grandMA2 Series

Brand: MA lighting Pages: 36

Pixie-4 Express

Brand: XIA Pages: 17

Brand: YASKAWA Pages: 68

Brand: Konig Pages: 73

Brand: process-informatik Pages: 8

Brand: Digitus Pages: 8

Brand: Endace Pages: 51

DesignCore RVP-TDA3 Series

Brand: D3 Pages: 34

PBE-5AC-300-ISO

Brand: Ubiquiti Pages: 28

Brand: East Coast Datacom Pages: 19

Brand: National Instruments Pages: 8

Brand: Supermicro Pages: 27

Brand: Z-Com Pages: 18

Brand: TRENDnet Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands