Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 221 / 553

background image

Item

Remarks

Domain name of
the MG interface

It corresponds to parameter

domainName

of the MG interface.

When the H.248 protocol is used, this
parameter must be configured if
parameter

MIDType

of the H.248

message is configured as the domain
name. Otherwise, the MG interface fails
to be started. In other situations, this
parameter is optional.

Device name of
the MG interface

It is supported only by the H.248
protocol, and corresponds to parameter

deviceName

of the MG interface that

uses the H.248 protocol.
When the H.248 protocol is used, this
parameter must be configured if
parameter

MIDType

of the H.248

message is configured as the domain
name. Otherwise, the MG interface fails
to be started. In other situations, this
parameter is optional.

Start negotiation
version of the H.
248 protocol for
the MG interface

It is recommended that you configure
this parameter to 0, which indicates the
negotiation is performed according to
the profile.
If the MGC interconnected with the MG
is provided by another vendor, the
profile must be configured.

Digitmap of an MG Interface

The digitmaps here are used for certain
special applications such as emergency
calls and emergency standalone. The
digitmaps for common phone services
are sent to the AG by the MGC, and
therefore such digitmaps need not be
configured on the AG. If the services
such as emergency calls and emergency
standalone are not required, the
digitmaps need not be configured.

Software Parameters of an
MG Interface

According to the service requirements,
the configuration of software
parameters determines whether the MG
interface supports the functions such as
dual homing and emergency
standalone.

Ringing Mode of an MG
Interface

According to the service requirements,
the ringing modes of the MG interface
need to be determined.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

210

«
...
219
220
221
222
223
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: T&D Pages: 122

Brand: Ebyte Pages: 14

Brand: Aztech Pages: 2

Brand: Dolphin Pages: 9

Brand: TP-Link Pages: 110

Brand: Alcatel-Lucent Pages: 60

B-Control Fader BCF2000

Brand: Behringer Pages: 13

Wisenet XRN-6410RB2-24TB

Brand: Hanwha Techwin Pages: 124

PD-9501-10GCO/AC

Brand: Microchip Technology Pages: 41

Brand: CTC Union Pages: 12

Brand: Cypress Semiconductor Pages: 32

Brand: Zapp Pages: 24

Brand: Billion Pages: 2

SteelCentral AppResponse 2170

Brand: Riverbed Pages: 166

Brand: Generic Pages: 51

StorageGRID Webscale SG5700 Series

Brand: NetApp Pages: 15

Brand: Cambium Networks Pages: 24

Brand: Cambium Networks Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands