Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 480 / 553

background image

Item

Data

Traffic
profile
parameters

Internet service: 1 Mbit/s
VoIP service: 64 Kbit/s
IPTV service: no limit

Uplink port
ID

0/0/1

Upstream
VLANs

Internet service: smart VLAN 102
VoIP service: smart VLAN 103
IPTV service: smart VLAN 104

User-side
802.1p
priorities

Internet service: 2
VoIP service: 3
IPTV service: 4

IGMP
version

IGMP v3 (default IGMP version in the multicast VLAN mode)

Multicast
source

Two multicast sources:
ISP 1: with IP address 10.10.10.10, providing the multicast program with IP
address 224.1.1.1
ISP 2: with IP address 10.10.10.11, providing the multicast program with IP
address 224.1.1.2

Multicast
program
library

Programs in multicast VLAN 104:
Program 1: with IP address 224.1.1.1, the program source IP address being
the same as the IP address of ISP 1 (10.10.10.10)
Program 2: with IP address 224.1.1.2, the program source IP address being
the same as the IP address of ISP 2 (10.10.10.11)

Right profile

Set right profile 0. Profile 0 has the right to watch program 1 in the program
library.

Multicast
users

User 1: User 1 (on port 0/3/0) can watch all the programs.
User 2: User 2 (on port 0/3/1) can watch only program 1.

Upstream
priority

The 802.1p priorities are used. The VoIP service has priority 6, IPTV service
priority 5, and Internet service priority 1.

Configuration Flowchart

Figure 9-15

shows the flowchart for configuring the triple play service in the single-PVC for

multiple services mode based on the user-side 802.1p priority.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

469

«
...
478
479
480
481
482
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Abocom Pages: 11

Brand: Abocom Pages: 19

Brand: National Instruments Pages: 11

inLab Speedcure 9494800

Brand: Dentsply Sirona Pages: 91

Brand: Caimore Pages: 79

Brand: Barco Pages: 121

OCTOPUS 5TX-EEC

Brand: Hirschmann Pages: 6

OMB-DAQBOARD-3000 Series

Brand: Omega Pages: 108

Brand: Altera Pages: 93

NetVanta 6355 PoE

Brand: ADTRAN Pages: 46

NVIP- NVRA0104/GO

Brand: Novus Pages: 44

Storage Networking (Unified Fabric Pilot)

Brand: Qlogic Pages: 76

Brand: ZALMAN Pages: 7

Octopus G Series

Brand: TwinMOS Pages: 29

Brand: Gemtek Systems Pages: 51

Brand: Kontron Pages: 19

Brand: RubyTech Pages: 25

Brand: Vecow Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands