Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 177 / 553

background image

Run

port vlan

command to add the upstream port to the VLAN.

Step 2

Configure the attribute of the upstream port.
If the default attribute of the upstream port does not meet the requirement for interconnection
of the upstream port with the upper-layer device, you need to configure the attribute. For
configuration details, see

3.3.1 Configuring an Uplink Ethernet Port

.

Step 3

Configure redundancy backup for the uplink.

To ensure reliability of the uplink, two upstream ports must be available. That is, redundancy
backup of the upstream ports needs to be configured. For details, see

3.4 Configuring the Link

Aggregation of Upstream Ethernet Port

.

----End

Example

Assume that the 0/0/1 and 0/0/0 upstream ports are to be added to VLAN 50. The 0/0/1 and
0/0/0 need to be configured into an aggregation group for double upstream accesses. For the two
upstream ports, the working mode is full-duplex (full) and the port rate is 100 Mbit/s. To
configure such upstream ports, do as follows:

huawei(config)#

port vlan 50 0/0 0

huawei(config)#

port vlan 50 0/0 1

huawei(config)#

interface eth 0/0

huawei(config-if-eth-0/0)#

duplex 0 full

huawei(config-if-eth-0/0)#

duplex 1 full

huawei(config-if-eth-0/0)#

speed 0 100

huawei(config-if-eth-0/0)#

speed 1 100

huawei(config-if-eth-0/0)#

quit

huawei(config)#

link-aggregation 0/0 0 0/0 1 egress-ingress workmode lacp-static

5.3 Configuring an xDSL Port

An xDSL can transmit services only when it is activated. This topic describes how to activate
an xDSL port and bind the port with an xDSL profile.

Prerequisites

The xDSL profile is already created.

l

3.7.1 Configuring the ADSL2+ Profile

l

3.7.2 Configuring the SHDSL Profile

l

3.7.3.1 Configuring the VDSL2 Profile (Normal Mode)

l

3.7.3.2 Configuring the VDSL2 Profile (TI Mode)

Context

l

Activating (or activation) refers to the training between the xTU-C and the xTU-R. During
the training process, the system checks the line distance and conditions and performs a
negotiation between the xTU-C and the xTU-R to determine whether the port can work
under the conditions as preset in the line profile, such as upstream and downstream line
rates and noise margin.

l

If the training is successful, the communication connection is set up between the xTU-C
and the xTU-R, and the devices are ready for service transmission. This state is called the

SmartAX MA5616 Multi-service Access Module
Configuration Guide

5 Configuring the xDSL Internet Access Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

166

«
...
175
176
177
178
179
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: BandLuxe Pages: 67

Brand: IBM Pages: 4

Avenue Express Control Panel

Brand: Ensemble Designs Pages: 19

Brand: Aztech Pages: 2

Brand: Juniper Pages: 7

Brand: Grundig Pages: 24

Brand: AXIOMTEK Pages: 2

NetVanta Serial Dial Backup Interface Module (DIM) none

Brand: ADTRAN Pages: 2

Brand: IBM Pages: 130

Brand: Promise Technology Pages: 148

Brand: TEC Control Pages: 4

Brand: e+p Pages: 2

Brand: National Instruments Pages: 147

SelectIO 7 Series

Brand: Xilinx Pages: 188

Brand: Proxim Pages: 89

Brand: Eaton Pages: 24

Brand: Velleman Pages: 14

Brand: Costar Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands