Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 18 / 553

background image

2

Checking Before the Configuration

About This Chapter

Before the service configuration, you need to check the software version and board status of the
MA5616 to ensure that the service runs normally after the configuration.

2.1 Checking the Software Version

This topic describes how to check whether the current software version meets the deployment
requirement.

2.2 Checking the Board Status

This topic describes how to check whether the inserted board is the same as the board specified
in the data plan, and whether the boards are in the normal state.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

2 Checking Before the Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

7

«
...
16
17
18
19
20
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Vb-C60 - Ptz Network Camera

Brand: Canon Pages: 30

Brand: D-Link Pages: 100

Brand: D-Link Pages: 134

Brand: D-Link Pages: 187

Brand: D-Link Pages: 225

Brand: D-Link Pages: 31

Brand: D-Link Pages: 35

DES-1016D - Switch

Brand: D-Link Pages: 19

Brand: D-Link Pages: 107

AirPlusXtremeG DI-624

Brand: D-Link Pages: 5

Brand: D-Link Pages: 48

Brand: B2 Pages: 52

Brand: National Instruments Pages: 9

Brand: National Instruments Pages: 24

Brand: National Instruments Pages: 32

FIELDPOINT FP-1600

Brand: National Instruments Pages: 8

F-ZTAT H8/3048 Series

Brand: Renesas Pages: 34

Brand: National Instruments Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands