Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 162 / 553

background image

To configure the power monitoring through the H831PMU (backup power using the Fe-lithium
battery) with such configurations, do as follows:

huawei(config)#

emu add 3 H831PMU 0 0 RS485

huawei(config)#

interface emu 3

huawei(config-if-h831pmu-3)#

power supply-parameter 59 48

Send command to environment monitor board ,please waiting for the ack

huawei(config-if-h831pmu-3)#
Execute command successful
huawei(config-if-h831pmu-3)#

quit

huawei(config)#

emu add 4 liBATTERY 0 23 rs485 battery1

huawei(config)#

interface emu 4

huawei(config-if-libattery-4)#

power batteryinstall 2010-08-20

huawei(config-if-libattery-4)#

display power run info

EMU ID: 4 LiBattery run information
----------------------------------------------------------------------------
Battery charge state: Charge
Battery voltage: 54.01V
Battery current: 0.82A
Battery temperature: 29°C
Battery capacity specification: 10A
Battery capacity remained percentage: 97%
Battery charge or discharge number: 13
The sum of discharge capacity: 106Ah
----------------------------------------------------------------------------
huawei(config-if-libattery-4)#

quit

huawei(config)#

save

3.15.3 Configuring the Monitoring Through the Fan

This topic describes how to configure the speed adjustment mode and the alarm function of the
fan. Thus, the fan speed of the MA5616 can be adjusted automatically, and the fan tray of the
MA5616 can be monitored.

Context

The fan tray requires the RS-232 serial port for data communication.

The subnode ID of the fan tray is invariably 2.

Procedure

Step 1

Add an EMU.

Run the

emu add

command to add an EMU.

Step 2

Configure the speed adjustment mode of the fan.

Run the

fan speed

command to configure the speed adjustment mode of the fan. By default, the

fan speed adjustment mode is automatic.

NOTE

When the fan speed adjustment mode is the manual mode, you can run the

fan speed adjust

command to set

the fan speed. The speed level can be 0, 1, 2, 3, 4, or 5. Here, 5 stands for the highest level, and 0 stands for the
lowest level.

Step 3

Configure whether alarms associated with the fan tray are reported.

Run the

fan alarmset

command to configure the reporting of alarms related to the fan tray.

Step 4

Query the configuration parameters of the fan tray.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

151

«
...
160
161
162
163
164
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: BandLuxe Pages: 67

Brand: Farallon Pages: 26

Brand: Observint Pages: 11

Brand: Patton electronics Pages: 51

Brand: N-Tron Pages: 62

Brand: NETGEAR Pages: 84

Brand: Macsense Pages: 13

Brand: TP-Link Pages: 7

ipRocketLink IAD 3086

Brand: Patton electronics Pages: 12

Brand: NetComm Pages: 75

Brand: Proscend Pages: 93

Xtreme Networked Boat

Brand: Broadband Products Pages: 16

Brand: HYCON Pages: 13

Brand: Datel Pages: 8

Brand: Exibel Pages: 2

PCIe Gen1 Framegrabbers

Brand: EDT Pages: 43

Brand: Jennic Pages: 14

BiPAC 8200AXL-1200

Brand: Billion Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands