manualshive.com logo in svg

Huawei SmartAX MA5616, Configuration Manual

The Huawei SmartAX MA5616 Configuration Manual is a detailed and comprehensive guide that enables users to efficiently set up and optimize their Huawei SmartAX MA5616. Easily downloadable for free from manualshive.com, this manual provides step-by-step instructions and essential information to maximize your product experience.

Share
Download
background image

  0  /3 /31   0        83110031         Cat3     DEL          A31               
  ------------------------------------------------------------------------    

7.1.2.2 (Optional) Configuring the System Parameters

This topic describes how to configure the system parameters including the overseas version flag
and message waiting indication (MWI) mode according to the local standards to ensure that the
response of the user terminal complies with the local standards.

Context

Table 7-6

 lists the system parameters supported by the MA5616.

Table 7-6

 System parameters supported by the MA5616

Parameter

Description

Default Setting

0

Indicates the howler tone
sending flag.

1: Indicates that the howler tone
is sent.

1

Indicates the overseas version
flag.

0: Indicates China.

2

Indicates the initial ringing stop
flag.

0: Indicates that the initial
ringing stop flag is not issued.

3

Indicates the MWI mode.

1: Indicates that the FSK is sent
with ringing.

4

Indicates the global digitmap
support flag.

1: Indicates that the global
digitmap is supported.

5

Indicates the media stream
forwarding mode on the same
device.

0: Indicates that the media stream
is forwarded within the device.

6

Indicates whether to send
power deny flag when
softswitch indicates block.

1: Not send

 

Procedure

Step 1

Run the 

system parameters

 command to configure the system parameters.

Step 2

Run the 

display system parameters

 command to check whether the system parameters are the

same as the planned data.

----End

Example

To configure the overseas version flag (system parameter 1) to Hong Kong (parameter value 1),
do as follows:

huawei(config)#

system parameters 1 1

                      

huawei(config)#

display system parameters 1

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

235

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

PACOM Professional Series Quick Manual preview
Professional Series
Brand: PACOM Pages: 15
X-Micro WLAN 11g User Manual preview
WLAN 11g
Brand: X-Micro Pages: 74
Roland VP-9000 Turbostart preview
VP-9000
Brand: Roland Pages: 2
Realtek RTL8187SE User Manual preview
RTL8187SE
Brand: Realtek Pages: 30
hilscher CIFX 104 User Manual preview
CIFX 104
Brand: hilscher Pages: 154
Intel F-Tile SDI II Intel Agilex User Manual preview
F-Tile SDI II Intel Agilex
Brand: Intel Pages: 39
RAIDAGE DAGE312UTL-NAS User Manual preview
DAGE312UTL-NAS
Brand: RAIDAGE Pages: 60
Advantech 3718HG User Manual preview
3718HG
Brand: Advantech Pages: 68
Kontron MSP8040 Series User Manual preview
MSP8040 Series
Brand: Kontron Pages: 32
Vivotek TB5328 SERIES User Manual preview
TB5328 SERIES
Brand: Vivotek Pages: 317
Pro-Nets Technology Corporation WR750RL User Manual preview
WR750RL
Brand: Pro-Nets Technology Corporation Pages: 48
Patton electronics OnSite 9100 Quick Start Manual preview
OnSite 9100
Brand: Patton electronics Pages: 8
Roland Symphonique Strings SRX-04 Owner'S Manual preview
Symphonique Strings SRX-04
Brand: Roland Pages: 12
TECO e-chill 1 Instruction Manual preview
e-chill 1
Brand: TECO Pages: 24
Allied Telesis 613-50550-00 Installation Manual preview
613-50550-00
Brand: Allied Telesis Pages: 2
Waver Smart One WAC52G Quick Start Manual preview
Smart One WAC52G
Brand: Waver Pages: 36
Balluff BNI EIP-508 05-Z015 Series User Manual preview
BNI EIP-508 05-Z015 Series
Brand: Balluff Pages: 74
Curtiss-Wright GTS/DEC/006 Instructions Manual preview
GTS/DEC/006
Brand: Curtiss-Wright Pages: 10

Brands by name

Popular brands

Load more brands