manualshive.com logo in svg

Huawei SmartAX MA5616, Configuration Manual

The Huawei SmartAX MA5616 Configuration Manual is a detailed and comprehensive guide that enables users to efficiently set up and optimize their Huawei SmartAX MA5616. Easily downloadable for free from manualshive.com, this manual provides step-by-step instructions and essential information to maximize your product experience.

Share
Download
background image

 MGID                   :0
 Nego-mode              :self-switch
 Rtp-interval           :10ms
 Vbd-codec              :G.711A
 Vbd-pt-type            :static
 Vbd-attribute-type     :v.152
 -------------------------------------------------------------------------------
huawei(config-if-sip-0)#

fax parameters transmode 0

huawei(config-if-sip-0)#

quit

huawei(config)#

display fax parameters

{ <cr>|mgid<U><0,16777215> }:

0

  Command:
          display fax parameters 0
 ---------------------------------------                                        
 MGID      Transmode                                                            
 ---------------------------------------                                        
 0         Thoroughly                                                           
 ---------------------------------------                                        

7.6 Configuring the MoIP Service (Based on the H.248
Protocol)

This topic describes how to configure the MoIP service when the H.248 protocol is used to
transmit the modem data service over the IP network.

Prerequisites

l

The communication between the MG and the MGC must be in the normal state.

l

The voice service port used by the MoIP service and the voice service on that port must be
in the normal state.

Context

The MA5616 supports the self-switch mode and the auto-negotiation mode:

l

Self-switch: If the self-switch mode is configured, the modem working mode of the
MA5616 is not controlled by the MGC. Therefore, manual configuration is required.

l

Auto-negotiation: If the auto-negotiation mode is configured, the modem working mode
of the MA5616 is automatically configured during the negotiation with the MGC.
Therefore, manual configuration is not required.

The MA5616 supports the 10 ms packing function and the RFC 2198 function.

l

10 ms packing function: In addition to the 20 ms G.711 transparent transmission, the modem
transparent transmission function is added with the 10 ms G.711 transparent transmission.
This reduces delay, improves the performance of transparent transmission, and decreases
the impact of packet loss on the transmission of the modem service data.

l

RFC 2198 function: Through the redundant transmission, the RFC 2198 improves the
reliability of data transmission. When the network packet loss occurs, the RFC 2198 can
ensure the service quality.

The MoIP service supports two transmission modes: the transparent transmission mode and the
relay (redundancy) mode. The MA5616 supports only the modem service in the transparent
transmission mode. In the transparent transmission mode, the MG uses the G.711 mode to encode
and decode the modem signal, and processes the signal like processing the common RTP data.
The transparent transmission mode depends on the bearer network to a great extent.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

302

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

TC Electronic M300 Service Manual preview
M300
Brand: TC Electronic Pages: 2
D-Link DWR-112 Technical Support Setup Procedure preview
DWR-112
Brand: D-Link Pages: 11
D-Link DSR-250 Cli Reference Manual preview
DSR-250
Brand: D-Link Pages: 83
D-Link DSR-150 Reference Manual preview
DSR-150
Brand: D-Link Pages: 129
D-Link DSL-G804V Manual preview
DSL-G804V
Brand: D-Link Pages: 10
D-Link DSL-G804V Quick Information Manual preview
DSL-G804V
Brand: D-Link Pages: 21
D-Link DSL-2750E Quick Start Manual preview
DSL-2750E
Brand: D-Link Pages: 6
D-Link DSL-2750E Technical Support Setup Procedure preview
DSL-2750E
Brand: D-Link Pages: 17
D-Link DSL-2740U Setup Manual preview
DSL-2740U
Brand: D-Link Pages: 4
D-Link DSL-2730B How To Set Up preview
DSL-2730B
Brand: D-Link Pages: 6
D-Link DSL-520T Quick Installation Manual preview
DSL-520T
Brand: D-Link Pages: 86
D-Link DSL-502T Installing Usb Drivers preview
DSL-502T
Brand: D-Link Pages: 3
D-Link DSL-3900 Quick Start Manual preview
DSL-3900
Brand: D-Link Pages: 4
D-Link DWR-921 How To Set Up preview
DWR-921
Brand: D-Link Pages: 4
D-Link DSL-3580L Series Quick Installation Manual preview
DSL-3580L Series
Brand: D-Link Pages: 20
D-Link DSL-3785 Quick Installation Manual preview
DSL-3785
Brand: D-Link Pages: 64
D-Link DSL-224 User Manual preview
DSL-224
Brand: D-Link Pages: 73
Lanpro LP-N24 Installation Instructions preview
LP-N24
Brand: Lanpro Pages: 5

Brands by name

Popular brands

Load more brands