manualshive.com logo in svg

Huawei SmartAX MA5616, Configuration Manual

The Huawei SmartAX MA5616 Configuration Manual is a detailed and comprehensive guide that enables users to efficiently set up and optimize their Huawei SmartAX MA5616. Easily downloadable for free from manualshive.com, this manual provides step-by-step instructions and essential information to maximize your product experience.

Share
Download
background image

l

The 10 ms packing function and the RFC2198 intelligent startup function are enabled.

l

The transmission mode of the modem event is ControlledByMGC (default).

l

The codec mode of the VBD is G.711A (default).

l

The payload type of the VBD is static payload (default).

l

The working mode of modem is transparent transmission (thoroughly).

l

The report mode of the modem event is direct.

To configure the MA5616, do as follows:

huawei(config)#

fax-modem parameters negomode selfswitch packet-interval-10ms 

enable
rfc2198-start-mode enableRfc2198SmartStartup transevent controlledByMGC
vbd-codec G.711A vbd-pt-type static

huawei(config)#

modem parameters tranmode 0 eventmode 1

huawei(config)#

display fax-modem parameters

  -----------------------------------------------------------------------------
  Negomode               : Self switch
  Packet-interval-10ms   : Enable
  Rfc2198-start-mode     : Enable Rfc2198SmartStartup
  TransEvent             : ControlledByMGC
  Vbd-codec              : G.711A
  Vbd-payload-type       : Static
  -----------------------------------------------------------------------------
huawei(config)#

display modem parameters

  -----------------------------------------------------------------------------
  MODEM transfers mode                   :Thoroughly
  MODEM event mode                       :Direct
  -----------------------------------------------------------------------------

7.7 Configuring the MoIP Service (Based on the SIP
Protocol)

This topic describes how to configure the MoIP service when the SIP protocol is used to transmit
the modem data service over the IP network.

Prerequisites

l

The communication between the MA5616 and the IMS must be in the normal state.

l

The VoIP service must be configured, see 

7.2.2 Configuring the VoIP PSTN User

.

l

The voice service port used by the MoIP service and the voice service on that port must be
in the normal state.

Context

The MA5616 supports the self-switch mode and the auto-negotiation mode:

l

Self-switch: If the self-switch mode is configured, you need to configure the fax working
mode of the MA5616 manually.

l

Auto-negotiation: If the auto-negotiation mode is configured, you need to configure the fax
working mode of the MA5616 manually.

The MA5616 supports the 10 ms packing function and the RFC 2198 function.

l

10 ms packing function: In addition to the 20 ms G.711 transparent transmission, the modem
transparent transmission function is added with the 10 ms G.711 transparent transmission.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

304

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

D-Link Verizon DSL-2750B Connection Instructions preview
Verizon DSL-2750B
Brand: D-Link Pages: 2
D-Link DVA-2800 Quick Start Manual preview
DVA-2800
Brand: D-Link Pages: 4
Raidon SAFETank Series User Manual preview
SAFETank Series
Brand: Raidon Pages: 49
M86 Security R3000 Series Evaluation Manual preview
R3000 Series
Brand: M86 Security Pages: 46
RadiSys EPC-31 Hardware Reference Manual preview
EPC-31
Brand: RadiSys Pages: 44
Blackrock Microsystems Cerebus Instructions For Use Manual preview
Cerebus
Brand: Blackrock Microsystems Pages: 27
Conceptronic C150BRS4 Multi Language Quick Manual preview
C150BRS4
Brand: Conceptronic Pages: 2
Avolites Titan One Quick Start Manual preview
Titan One
Brand: Avolites Pages: 24
ZyXEL Communications XGS4700 Series Manual preview
XGS4700 Series
Brand: ZyXEL Communications Pages: 485
IDT DBP 7+4 User Manual preview
DBP 7+4
Brand: IDT Pages: 93
UNA AUTOMATION DIFRA Installation Manual preview
DIFRA
Brand: UNA AUTOMATION Pages: 20
Datasat DDR-16 AES67 Installation And Operating Manual preview
DDR-16 AES67
Brand: Datasat Pages: 24
UfiSpace S9600-28DX Hardware Installation Manual preview
S9600-28DX
Brand: UfiSpace Pages: 34
Trend Micro IPS Pro-Module-24C-GE-BP-TM Quick Setup Manual preview
IPS Pro-Module-24C-GE-BP-TM
Brand: Trend Micro Pages: 3
SafeHome NVR903 Manual preview
NVR903
Brand: SafeHome Pages: 24
Dataprobe iBoot Instruction Manual preview
iBoot
Brand: Dataprobe Pages: 16
PADAUK PDK5S-P-003 User Manual preview
PDK5S-P-003
Brand: PADAUK Pages: 27
UNICORECOMM UM620N User Manual preview
UM620N
Brand: UNICORECOMM Pages: 19

Brands by name

Popular brands

Load more brands