Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 94 / 553

background image

requirements. The configuration of PITP sub-option 90 takes effect only in the PITP P mode;
the PITP V mode does not support reporting the line parameters.

----End

Example

Assume the following configuration:

l

RAIO mode: user-defined mode

l

CID format for the ATM access mode: shelf ID/slot ID/port ID:VPI.VCI

l

CID format for the Ethernet access mode: shelf ID slot ID port ID:VLAN ID

To enable the PITP P function for the traffic stream with VLAN ID 30, do as follows:

huawei(config)#

raio-mode user-defined pitp-pmode

huawei(config)#

raio-format pitp-pmode cid atm anid atm frame/slot/port:vpi.vci

huawei(config)#

raio-format pitp-pmode cid eth anid eth frame/slot/port:vlanid

huawei(config)#

raio-format pitp-pmode rid atm plabel

huawei(config)#

raio-format pitp-pmode rid eth plabel

huawei(config)#

pitp enable pmode

huawei(config)#

vlan service-profile profile-id 1

huawei(config-vlan-srvprof-1)#

pitp enable

huawei(config-vlan-srvprof-1)#

commit

huawei(config-vlan-srvprof-1)#

quit

huawei(config)#

vlan bind service-profile 30 profile-id 1

To set the Ethernet protocol type of VBRAS packets to be the same as the Ethernet protocol
type of the upper-layer BRAS, namely, 0x8500, enable the PITP V function for the traffic stream
with VLAN ID 30, and configure the RAIO mode to common, do as follows:

huawei(config)#

raio-mode common pitp-vmode

huawei(config)#

pitp enable vmode

huawei(config)#

vlan service-profile profile-id 1

huawei(config-vlan-srvprof-1)#

pitp enable

huawei(config-vlan-srvprof-1)#

commit

huawei(config-vlan-srvprof-1)#

quit

huawei(config)#

vlan bind service-profile 30 profile-id 1

3.10.2 Configuring Anti-Theft and Roaming of User Accounts
Through DHCP

DHCP improves the user authentication security by adding the user physical location information
to the option82 field of the DHCP request packets initiated by the user, so as to prevent theft
and roaming of the user account.

Context

The option82 field contains the circuit ID (CID), remote ID (RID), and sub-option 90 field
(optional), which provides the information such as the user shelf ID, slot ID, port ID, VPI, and
VCI.

The MA5616 can work in the L2 DHCP forwarding mode. In the mode, anti-theft and roaming
of user accounts through DHCP option82 can be configured.

lists the default settings related to DHCP option82.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

83

«
...
92
93
94
95
96
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

i-bus KNX IPR/S 3.5.1

Brand: ABB Pages: 44

Brand: SUNRICH TECHNOLOGY Pages: 5

Proventia A1204

Brand: Internet Security Systems Pages: 42

RealPort Ethernet 10/100

Brand: Xircom Pages: 30

Brand: Tektronix Pages: 178

Brand: EVOC Pages: 57

Brand: IMC Networks Pages: 36

Brand: Unex Pages: 27

Brand: Keil Pages: 68

Brand: JAKA Pages: 37

H8S/2646 Series

Brand: Renesas Pages: 20

Brand: Socket Pages: 28

Brand: IEI Technology Pages: 136

Brand: Modecom Pages: 16

Brand: Taiwan Commate Computer Inc. Pages: 25

Brand: Greenlee Pages: 52

Brand: B&B Electronics Pages: 24

CentreCOM AT-3716XL

Brand: Allied Telesis Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands