Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 95 / 553

background image

Table 3-15

Default settings related to DHCP option82

Parameter

Default Setting

Status of the DHCP option82 function

Global status: disabled
VLAN-level status: enabled

Status of the DHCP sub-option 7
function

Disabled

Status of the DHCP sub-option 90
function

Disabled

Procedure

Step 1

Configure the relay agent information option (RAIO). Before using the DHCP function, you
must configure the RAIO.

Run the

raio-mode

command to set the RAIO mode.

l

Select

dhcp-option82

as the corresponding mode.

l

In the user-defined mode, you need to run the

raio-format

command to configure the RAIO

format, and select

dhcp-option82

as the corresponding mode. To configure the user-defined

format, mainly configure the RID in the CID. If the access mode is not selected, the
configured format is valid to all access modes. If the access mode is selected, the configured
format is valid to only this access mode. For details about the RAIO format, see the

raio-

format

command.

–

CID identifies the attribute information of the device.

–

RID identifies the access information of the user.

l

In other modes, the RID format is fixed and therefore it need not be configured manually.

Step 2

(Optional) Set the service port to allow or prohibit the user-side DHCP packets that carry the
option82 information.

l

Run the

dhcp-option82 permit-forwarding service-port

command to set the service port

to allow or prohibit the DHCP packets that carry the option82 information.
The system adds the device name, shelf ID, slot ID, and port ID to the option82 field of
DHCP packets to generate new packets. If the service port is set to allow the packets carrying
the option82 information, tagged packets are forwarded. If the service port is set to prohibit
the packets carrying the option82 information, tagged packets are dropped.

Step 3

Enable or disable the DHCP option82 function.

Run the

dhcp option82

command to enable the DHCP option82 function on the port. By default,

the DHCP option82 function is disabled globally.

The DHCP option82 function can be enabled or disabled at two levels. The DHCP option82
function takes effect only when it is enabled at both levels.

1.

Global DHCP option82 function: Run the

dhcp option82

command to enable the DHCP

option82 function globally. By default, the DHCP option82 function is disabled globally.

2.

VLAN-level DHCP option82 function:

SmartAX MA5616 Multi-service Access Module
Configuration Guide

3 Basic Configuration

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

84

«
...
93
94
95
96
97
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: E-TOP Pages: 76

TotalStorage SAN16M-R SAN

Brand: IBM Pages: 116

Brand: Google Pages: 14

ICS-G7748A Series

Brand: Moxa Technologies Pages: 10

Brand: Zonet Pages: 2

Brand: APARIAN Pages: 2

Fieldpoint cFP-RTD-124

Brand: National Instruments Pages: 15

WGR614 - Wireless-G Router Wireless

Brand: NETGEAR Pages: 116

Brand: Uniden Pages: 5

Brand: Caen Pages: 14

Brand: Crystal Vision Pages: 54

Brand: Vecow Pages: 61

POD-51EH-C541U-12

Brand: IceTech Pages: 8

Brand: Intel Pages: 154

Brand: Enterasys Pages: 62

Brand: ekwb Pages: 10

Brand: LevelOne Pages: 4

Symphonique Strings SRX-04

Brand: Roland Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands