Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 423 / 553

background image

activate 0 template-index 3
alarm-config 0 1
quit
service-port 3 vlan 50 vdsl mode ptm 0/1/0 inbound traffic-table index 5 outbound
traffic-table index 5
service-port desc 3 description Vlanid:50/vdsl/vpi:1vci:39/stacking
stacking label service-port 3 10
stacking inner-priority service-port 3 4
stacking inner-priority service-port 2 4
dhcp option82 enable
raio-mode user-defined dhcp-option82
raio-format dhcp-option82 cid anid frame/slot/port:vlanid
raio-format dhcp-option82 rid splabel
save

9.1.3 Configuration Example of the xDSL PPPoA Internet Access
Service

This topic describes how to configure a user so that the user can access the MA5616 in the xDSL
mode, and then access the Internet in the PPPoA mode at a rate of 2048 kbit/s.

Service Requirements

l

The user accesses the Internet in the PPPoA mode.

l

User packets, which carry a single VLAN tag, are transmitted in the upstream direction,
and the services of multiple users are converged into one VLAN. This is called the N:1
access.

l

PITP is enabled to protect user accounts from theft and roaming.

l

A traffic profile is adopted for rate limitation. The user access rate is 2048 kbit/s.

l

Dual GE ports are adopted for upstream transmission to ensure reliability. Link aggregation
is configured for the two upstream ports.

shows an example network of the xDSL PPPoA Internet access service.

Figure 9-3

Example network of the xDSL PPPoA Internet access service

Prerequisite

l

The number of xDSL ports is under the control of licenses. Make sure that sufficient licenses
are already requested.

l

Configure the AAA function.

–

To enable the AAA function on the device, see

3.12 Configuring AAA

SmartAX MA5616 Multi-service Access Module
Configuration Guide

9 Configuration Example of Services on the MA5616

Through GE Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

412

«
...
421
422
423
424
425
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: 3Com Pages: 48

LightSpeed Appliance QLS250

Brand: Quantum Pages: 12

ADSL 2/2+ Router with USB Port ADE-3410v2

Brand: Planet Pages: 62

Brand: SUNRICH TECHNOLOGY Pages: 5

Brand: Jøtul Pages: 20

Storage Networking (Unified Fabric Pilot)

Brand: Qlogic Pages: 76

Brand: NKE Pages: 15

Brand: Cameo Pages: 23

CNPS11X Extreme

Brand: ZALMAN Pages: 12

Brand: CalAmp Pages: 115

Brand: Solwise Pages: 7

Brand: Federal Signal Corporation Pages: 49

Brand: XAVI Technologies Corp. Pages: 63

UST510-52B-FL Series

Brand: AXIOMTEK Pages: 77

Brand: HMS Pages: 18

Brand: PairGain Pages: 76

Brand: c Pages: 32

Brand: IBM Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands