Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 339 / 553

background image

interface shl 0/4
activate 0 3
alarm-config 0 1
quit
service-port 2 vlan 50 shdsl mode ptm 0/4/0 inbound traffic-table index 5 outbound
traffic-table index 5
service-port desc 2 description Vlanid:50/shdsl/vpi:1vci:39/stacking
stacking label service-port 2 10
stacking inner-priority service-port 2 4
dhcp option82 enable
raio-mode user-defined dhcp-option82
raio-format dhcp-option82 cid anid frame/slot/port:vlanid
raio-format dhcp-option82 rid splabel
save

Configuration File for the VDSL access mode:

vlan 50 smart
vlan attrib 50 stacking
vlan forwarding 50 vlan-connect
port vlan 50 0/0 0
vdsl line-profile quickadd 3 snr 60 0 300 60 0 300
vdsl channel-profile quickadd 3 path-mode ptm interleaved-delay 8 2 inp 4 2 rate
128 10000 128 10000 2048 2048
vdsl channel-profile quickadd 3 path-mode ptm interleaved-delay 8 2 inp 4 2 rate
128 10000 128 10000 2048 2048
interface vdsl 0/1
deactivate 0
activate 0 template-index 3
alarm-config 0 1
quit
service-port 3 vlan 50 vdsl mode ptm 0/1/0 inbound traffic-table index 5 outbound
traffic-table index 5
service-port desc 3 description Vlanid:50/vdsl/vpi:1vci:39/stacking
stacking label service-port 3 10
stacking inner-priority service-port 3 4
stacking inner-priority service-port 2 4
dhcp option82 enable
raio-mode user-defined dhcp-option82
raio-format dhcp-option82 cid anid frame/slot/port:vlanid
raio-format dhcp-option82 rid splabel
save

8.1.3 Configuration Example of the xDSL PPPoA Internet Access
Service

This topic describes how to configure a user so that the user can access the MA5616 in the xDSL
mode, and then access the Internet in the PPPoA mode at a rate of 2048 kbit/s.

Service Requirements

l

The user accesses the Internet in the PPPoA mode.

l

User packets, which carry a single VLAN tag, are transmitted in the upstream direction,
and the services of multiple users are converged into one VLAN. This is called the N:1
access.

l

PITP is enabled to protect user accounts from theft and roaming.

l

A traffic profile is adopted for rate limitation. The user access rate is 2048 kbit/s.

shows an example network of the xDSL PPPoA Internet access service.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

328

«
...
337
338
339
340
341
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: Panasonic Pages: 4

Brand: LORD Pages: 9

Brand: Lorex Pages: 186

Brand: NETGEAR Pages: 169

Wireless Mini PCI Module

Brand: E-Tech Pages: 42

Brand: WaiLan Pages: 27

Brand: Longshine Pages: 27

Brand: Daedalon Pages: 6

Brand: QuickLink Pages: 8

Brand: Juniper Pages: 2

Brand: ZALMAN Pages: 18

Brand: IMC Networks Pages: 36

Brand: TP-Link Pages: 57

DVI-Vision-IP-Fiber

Brand: G&D Pages: 240

AlterPath Manager 2500

Brand: Cyclades Pages: 368

Brand: Acromag Pages: 35

Brand: Inspired Energy Pages: 5

NC-MCO - TECHNICAL

Brand: Crest Audio Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands