Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 340 / 553

background image

Figure 8-3

Example network of the xDSL PPPoA Internet access service

Prerequisite

l

The number of xDSL ports is under the control of licenses. Make sure that sufficient licenses
are already requested.

l

Configure the AAA function.

–

To enable the AAA function on the device, see

3.12 Configuring AAA

–

If the AAA function is implemented by the BRAS, a connection to the BRAS must be
established. The BRAS should be capable of identifying the VLAN tag of the
MA5616 in the upstream direction. For the identification purpose, the user name and
password for dial-up Internet access must be configured on the BRAS.

Procedure

Step 1

Create a VLAN.

Create smart VLAN 50.

huawei(config)#

vlan 50 smart

Step 2

Configure upstream ports.
Add upstream ports 0/0/0 to VLAN 50.

huawei(config)#

port vlan 50 0/0 0

Step 3

In the case of the ADSL access mode, follow this procedure.
1.

Configure an ADSL2+ profile. For details, see

3.7.1 Configuring the ADSL2+ Profile

.

The ID of the ADSL2+ line profile is 3, the downstream rate is 2048 kbit/s, the channel
mode is the interleave mode, the maximum interleave delay is 10 ms, and the SNR margin
is 6 dB.

huawei(config)#

adsl line-profile quickadd 3 snr 60 30 120 60 30 120

huawei(config)#

adsl channel-profile quickadd 3 interleaved-delay 10 10 rate

1024
2048 3096 1024 2048
3096

huawei(config)#

adsl line-template quickadd 3 line 3 channel1 3 60 70 channel2

3

2.

Activate the ADSL port. The port is port 0/2/0, and ADSL line template 3 and the default
alarm template (alarm template 1) are bound to the port.

NOTE

By default, an ADSL port is in the activated state. Before binding a template to the port, you must deactivate
the port.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

329

«
...
338
339
340
341
342
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: GE Pages: 4

Brand: Garland Pages: 4

Brand: Icidu Pages: 10

Brand: Paradox Pages: 4

Brand: IDT Pages: 281

DMX-Universal-Demux

Brand: DMX4ALL Pages: 17

Brand: Rockwell Automation Pages: 108

Brand: Supermicro Pages: 16

NVIP- NVRA0104/GO

Brand: Novus Pages: 44

Brand: XtendLan Pages: 52

Vortex86SX VSX-6100

Brand: ICOP Technology Pages: 50

Brand: Idis Pages: 16

Brand: ZIMO Pages: 13

Brand: Dantel Pages: 22

Brand: Planet Pages: 16

Brand: Vivotek Pages: 46

7798 I/SITE LAN

Brand: CSI Pages: 56

Brand: Intercel Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands