Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 333 / 553

background image

8.1.2 Configuration Example of the xDSL IPoE Internet Access
Service

This topic describes how to configure a user so that the user can access the MA5616 in the xDSL
mode, and then access the Internet in the IPoE mode at a rate of 2048 kbit/s.

Service Requirements

l

The user accesses the Internet in the IPoE mode. The account authentication is implemented
through the DHCP option 82 field.

l

Double VLAN tags are added to user packets for upstream transmission, where the outer
VLAN tag identifies the service and the inner VLAN tag identifies the user. The service
of each user is identified by a unique S-VLAN+C-VLAN. This is called the 1:1 access.

l

A traffic profile is adopted for rate limitation. The user access rate is 2048 kbit/s.

shows an example network of the xDSL IPoE Internet access service.

Figure 8-2

Example network of the xDSL IPoE Internet access service

Prerequisite

The number of xDSL ports is under the control of licenses. Make sure that sufficient licenses
are already requested.

Procedure

Step 1

Configure a VLAN.

Configure S-VLAN 50 with the stacking attribute. The user packet goes upstream carrying two
VLAN tags. The outer VLAN tag identifies the service and the inner VLAN tag identifies the
user. The service of each user is identified by unique S-VLAN+C-VLAN, and the VLAN
forwarding mode is the S-VLAN+C-VLAN mode.

huawei(config)#

vlan 50 smart

huawei(config)#

vlan attrib 50 stacking

huawei(config)#

vlan service-profile profile-id 1

huawei(config-vlan-srvprof-1)#

forwarding vlan-connect

huawei(config-vlan-srvprof-1)#

commit

huawei(config-vlan-srvprof-1)#

quit

huawei(config)#

vlan bind service-profile 50 profile-id 1

Step 2

Configure upstream ports.
Add upstream ports 0/0/0 to VLAN 50.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

322

«
...
331
332
333
334
335
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: D-Link Pages: 99

Brand: D-Link Pages: 5

Brand: D-Link Pages: 15

AirPro DWL-6000AP

Brand: D-Link Pages: 65

Brand: D-Linke Pages: 32

Brand: IDT Pages: 281

DMX-Universal-Demux

Brand: DMX4ALL Pages: 17

Brand: Rockwell Automation Pages: 108

Brand: Renesas Pages: 941

Brand: TANDBERG Pages: 3

Brand: Ruckus Wireless Pages: 2

Brand: Rosewill Pages: 10

Brand: Patton electronics Pages: 2

Brand: Lanner Pages: 78

Brand: Z3 Technology Pages: 87

Brand: MEDIATEK Pages: 166

Kontron SMARC-sXEL

Brand: S&T Pages: 108

Brand: LevelOne Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands