Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 319 / 553

background image

-------------------------------------------------
APPENDIX:
-------------------------------------------------
Interface software parameter name:
6: Whether MG supports authentication
0: Yes
1: No
huawei(config-if-h248-0)#

auth auth_mgid MA5616 initial_key 0123456789ABCDEF

huawei(config-if-h248-0)#

display auth

[AUTH_PARA config]
Initial Key : 0123456789ABCDEF
Auth MGid : MA5616
Algorithm : MD5
huawei(config-if-h248-0)#

reset coldstart

Are you sure to reset MG interface?(y/n)[n]:

y

7.8.1.2 Configuring the Device Authentication (Based on the SIP Protocol)

This topic describes how to configure the authentication information for the SIP interface or a
single user of the MA5616 when the SIP protocol is used.

Prerequisites

l

The SIP interface must be added successfully on the MA5616.

l

The authentication user name and password must be configured on the IMS. Such
parameters must be the same as the authentication user name and password configured on
the MA5616.

Context

l

The authentication information can be configured for the SIP interface. The configuration
takes effect only after you run the

reset

command on the SIP interface.

l

The authentication information can be configured for a single user. The configuration takes
effect immediately after the configuration is complete.

l

In the actual application, whether the user uses the authentication information configured
for the SIP interface or a single user can be controlled through system parameter 81 in the

sipprofile modify

command.

Procedure

l

Configure the authentication information for the SIP interface.

1.

In the global config mode, run the

interface sip

command to enter the SIP interface

mode.

2.

Run the

sip-auth-parameter

command to configure the authentication user name and

password for an SIP interface.

3.

Run the

display sip-auth

command to query the authentication information of an SIP

interface.

4.

Run the

reset

command to reset the SIP interface.

l

Configure the authentication information for a single user.

1.

Run the

esl user

command to enter the ESL user mode.

2.

Run the

sippstnuser auth set

command to configure the authentication user name

and password for a single user.

SmartAX MA5616 Multi-service Access Module
Configuration Guide

7 Configuring the Voice Service

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

308

«
...
317
318
319
320
321
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Express Ethernetwork DI-704P

Brand: D-Link Pages: 2

Brand: D-Link Pages: 11

Brand: D-Link Pages: 8

AirPlus DWL-810

Brand: D-Link Pages: 8

Brand: D-Link Pages: 12

Brand: D-Link Pages: 84

Brand: Aastra Pages: 2

Brand: LAWO Pages: 154

Brand: Xinje Pages: 57

xCORE-200 Multi-channel Audio board

Brand: XMOS Pages: 112

Brand: D-Link Pages: 83

Brand: iDirect Pages: 52

IAR KickStart Kit TWR-K60N512-IAR

Brand: IAR SYSTEMS Pages: 8

Brand: Dantel Pages: 62

Low Power Series

Brand: FabiaTech Pages: 77

Brand: Cowfish Technologies Pages: 38

Brand: AOpen Pages: 18

Brand: National Instruments Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands