Huawei SmartAX MA5616 Configuration Manual Download | Manualshive

Page: 387 / 553

background image

6
tx-cttr 6

Set the inner VLAN tag.

stacking label service-port 0 11
stacking label service-port 1 12

Configuration file of MA5616_B

Create a VLAN.

vlan 101 smart

Set the VLAN attribute to stacking VLAN.

vlan attrib 101 stacking

Add an uplink port to the VLAN.

port vlan 101 0/0 1

Add service ports to the VLAN.

service-port 0 vlan 101 vdsl mode ptm 0/1/2 multi-service user-encap pppoe rx-cttr
6
tx-cttr 6
service-port 1 vlan 101 vdsl mode ptm 0/1/3 multi-service user-encap pppoe rx-cttr
6
tx-cttr 6

Set the inner VLAN tag.

stacking label service-port 0 11
stacking label service-port 1 12

8.5 Configuring the Triple Play Service

This topic describes the triple play service and how to configure the triple play service on the
MA5616 that is used on the GPON upstream transmission network.

8.5.1 Configuring the Triple Play Service - Single PVC for Multiple
Services Based on the User-Side VLAN

This topic describes how to configure the triple play service in the single-PVC for multiple
services mode (based on the user-side VLAN).

Prerequisites

Before configuring the triple play service, make sure that:

l

The network devices and lines are in the normal state.

l

The CPE is already configured (the CPE supports different VLANs for different services).

l

All boards of the device run in the normal state.

l

The VDSL2 line template and alarm template that are bound to the port are already
configured. For details on the configuration procedure, see

3.7.3 Configuring the VDSL2

SmartAX MA5616 Multi-service Access Module
Configuration Guide

8 Configuration Example of Services on the MA5616

Through GPON Upstream Transmission

Issue 04 (2011-10-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

376

«
...
385
386
387
388
389
...
»

Summary of Contents for SmartAX MA5616










































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SmartAX MA5616

Brand: GE Pages: 146

Brand: Panasonic Pages: 4

Brand: Patton electronics Pages: 51

Brand: ebm-papst Pages: 16

InterReach Fusion ADCP-77-044

Brand: TE Connectivity Pages: 236

Brand: BSS Audio Pages: 20

Brand: Reeven Pages: 2

tBOX330-870-FL Series

Brand: AXIOMTEK Pages: 2

Brand: Funkwerk Pages: 2

BIC 1I12-P2A25-M30MI1-BPX05-110

Brand: Balluff Pages: 12

Brand: Neo Instruments Pages: 2

Thin Client US310e

Brand: NEC Pages: 6

Brand: Patton electronics Pages: 2

Brand: Lanner Pages: 78

Brand: Z3 Technology Pages: 87

ConnectX-3 Pro MCX349A-XCCN

Brand: Mellanox Technologies Pages: 35

IPLink 2603 Series

Brand: Patton Pages: 120

Brand: Ubiquiti Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands