manualshive.com logo in svg

Avaya G700, Installing And Upgrading, Page: 754 / 808

Share
Download
Avaya G700 Installing And Upgrading Download Page 754

Manual upgrade of an existing S8300B and G700 to S8300C with R4.0

754 Installing and Upgrading the Avaya G700 Media Gateway and Avaya S8300 Media Server

 

To check media modules 

1. Type 

list configuration all

 and press 

Enter

. 

2. Verify that the software is communicating with all media modules and that all media 

modules are listed in the reports. 

3. Make test telephone calls to verify that Communication Manager is working. 

To enable scheduled maintenance 

1. Type 

change system-parameters maintenance

 and press 

Enter

. 

2. Ensure that the 

Start Time

 and 

Stop Time

 fields' administration is the same as before the 

upgrade. 

To busy out trunks 

1. Busy out trunks that were busied out before the upgrade (see 

To record all busyouts

on 

page 702). 

To check for translation corruption 

1. Type 

newterm

 and press 

Enter

. 

If you do not get a login prompt and see the following message: 

Warning: Translation corruption detected 

follow the normal escalation procedure for translation corruption before continuing the 
upgrade. 

To resolve alarms 

1. On the Maintenance Web Interface, under Alarms click 

Current Alarms

 to examine the 

alarm log. 

2. If any alarms are listed, click 

Clear All

.

3. Resolve new alarms since the upgrade through Communication Manager using the 

appropriate maintenance book. 

Summary of Contents for G700









































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments