Avaya G700 Installing And Upgrading Download Page 455

Page: 455 / 808

Install New Firmware on the G700

Issue 10.2 May 2007

455

3. At the

MG-001-1(configure)#

prompt, type

set mgp reset-times

transition-point

<#_of_primary>

where

<#_of_primary>

is the number of primary controllers in the controller list. If the

primary controller is an S8500 or S8700/S8710/S8720, the range is

from

If the

primary controller is an S8300,

<#_of_primary>

must be

Configuring an X330 Expansion Module (If Necessary)

User Guides and Quick Start Guides for the expansion modules are available on the Avaya
Support web site:

To obtain the appropriate Avaya Support Web site document

1. Go to the Avaya Support web site:

http://avaya.com/support

2. In the list on under Technical Database, click on

LAN, Backbone,

and

Edge Access

Switches

3. Under Wiring Closet & Distribution, click on

P330 Stackable Switching

4. Click on

All Documents

5. Select the appropriate document for the expansion module you are installing.

Install New Firmware on the G700

This section describes the manual procedures to install firmware on the G700 Media Gateway
processors and media modules.

Manual upgrade procedures — G700 firmware

This section contains the following tasks:

●

Verifying the Contents of the tftpboot Directory

●

Determining which firmware to install on the G700

●

Installing New Firmware on the P330 Stack Processor

●

Installing new firmware on the G700 Media Gateway Processor

●

Installing new firmware on the media modules

Summary of Contents for G700









































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for G700

Reviews:

Avaya G700, Installing And Upgrading, Page: 455 / 808

Search results

Summary of Contents for G700

Reviews: