manualshive.com logo in svg

Avaya G700, Installing And Upgrading, Page: 239 / 808

Share
Download
Avaya G700 Installing And Upgrading Download Page 239

Administer Communication Manager

Issue 10.2 May 2007

239

 

6. Press 

F3

 (

Enter

) to save your changes. 

If properly administered, the G700 should register with the primary controller within 1–2 
minutes. The 

IP Address

, 

MAC Address

, and 

Module Type

 fields are populated 

automatically after the G700 media gateway registers with the server.

7. Type 

change media-gateway

 to view the 

Media Gateway

 screen.

Media Gateway screen (after registration with primary controller) 

The media modules installed in the G700 are listed next to their slot numbers. Verify that a 
G700 media gateway has been successfully added.

To verify changes

1. At the SAT prompt, type 

list media-gateway

.

Media-Gateway Report screen 

change media-gateway 1 

Page  1 of 1

MEDIA GATEWAY

Number: 1

Registered: y

Type: g700

FW Version/HW Vintage: 21.13.0 /0

Name: Swainsons 

 

 IP Address: 135.9.41.150

Serial No: 012X06230551

Controller IP Address: 135.9.41.146

Encrypt Link? y 

MAC Address: 

Network Region: 1 

 

CF: 8 MB

Location: 1

Site Data: 

Recovery Rule: none

Slot Module 

Type

Name

V1:

S8300

ICC MM

V2:

MM712

DCP MM

V3:

MM711

ANA MM

V4:

MM710

T1/E1 MM

V9:

list media-gateway

MEDIA-GATEWAY REPORT

Number 

Name 

Serial No/

IP Address/

Type   NetRgn  Reg?

FW Ver/HW Vint

Cntrl IP Addr 

RecRule

1 LabA 

01DR07128730 

135.177.49.57 g700

1

y

21 .13 .0  /0

135.177.49.59

1

2 Data 

MG2

02DR01130356 

135.177.49.90 g350

1

n

11 .2

.0

/0

135.177.49.40

none

Summary of Contents for G700









































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments