Avaya G700 Installing And Upgrading Download Page 500

Page: 500 / 808

Manual installation of a new G700 without an S8300

500 Installing and Upgrading the Avaya G700 Media Gateway and Avaya S8300 Media Server

4. Double-click the file name.

The system displays a

File Download

window.

5. Click on

Save this file to disk

6. Save the file to the

C:\tftp

directory (or your alternate tftp location).

7. Use WinZip or another zip file tool to unzip the file, if necessary.

Configure the G700

For a new installation of a G700 Media Gateway, you must complete the following configuration
tasks:

Assigning the IP addresses of the G700 media gateway components

Setting up the controller list for the G700

8-port/trunk Analog Media Module
(version 6 or earlier)

mm711<version id>

mm711v17.fdl

8-port/trunk Analog Media Module
(version 7)

mm711<version id>

mm711h7v24.fdl

8-port/trunk Analog Media Module
(version 20 or later)

mm711<version id>

mm711h20v68.fdl

4-station/4-CO trunk Analog
Media Module

mm714<version id>

mm714v67.fdl

T1/E1 Media Module

mm710<version id>

mm710v14.fdl

8-port BRI Media Module

mm720<version id>

mm720v6.fdl

2-port BRI Media Module

mm722<version id>

mm722v2.fdl

Table 32: Firmware file formats (continued)

Component

Firmware Version
Format

Example

2 of 2

Summary of Contents for G700









































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for G700

Reviews:

Avaya G700, Installing And Upgrading, Page: 500 / 808

Search results

Summary of Contents for G700

Reviews: