Product Features
139
© 2017, ATEÏS, member of PAX ProAV Group
The v alue is 0 if the mic is working.
If the Modbus Channel will not be set, the v alue is 0.
Only the PSS and PPM remote can detect the microphone fault.
RemoteSpeakerFault
If set Modbus Channel
If speaker fault, the v alue is 1.
If normal, the v alue is 0.
If do not set Modbus Channel, the v alue is 0.
Only PSS can detect speaker fault.
NumUserFaults
The number of User Define Item
User need create Fault Define Security component in the config.
Each IDA8 unit reserv e 8 fault item, if total 5 IDA8 units in the system, the number of User Faults is 8 x 5 = 40.
UserFaults
User Fault Status
UserFault
User Fault Class: Users need create Fault Define Security component in the configuration, the pin 1~8 is mapping to fault
item 1~8, the pin 9 and more is not display. Each IDA8 unit reserv e 8 node fix ev en if do not create Fault Define Security
component.
Node 1 ~ 8 = 1st IDA8 of Fault Define Security component.
Node 9 ~ 16 = 2nd IDA8 of Fault Define Security component.
Node 17 ~ 24 = 3rd IDA8 of Fault Define Security component ...and so on.
If configured the system with ATEIS Global-Net, the node order will local net units first, then global net units. For
example: IDA8C(1, 1), IDA8S(1, 2), IDA8S(1, 3), IDA8C(2, 1), IDA8S(2, 2), IDA8C(3, 1)
Node 1 ~ 8 = IDA8 (1, 1)
Node 9 ~ 16 = IDA8 (1, 2)
Node 17 ~ 24 = IDA8 (1, 3)
Node 25 ~ 32 = IDA8 (2, 1)
Node 33 ~ 40 = IDA8 (2, 2)
Node 41 ~ 48 = IDA8 (3, 1)
UserFaultIndex
Fault Index uniquely, from 1 to N.
UserFaultName
This User Fault name is the same with the name in Fault Define Security component.
UserFaultType
The v alue 1 if the type is Major, 0 if type is Minor
UserFaultStatus
If Fault Define Security is not created or the pin is not connected, the v alue is 0.
If Fault Define Security has created and the pin is connected:
The v alue is 1 if the fault is deactiv ated.
The v alue is 2 if the fault is activ ated.
If the IDA8 unit is offline, the v alue do not change.
3.1.20 Contact I/O
3.1.20.1 Evaction Input
The IDA8 processors have the evacuation inputs that allow the monitoring of external contacts. To
configure the evacuation inputs, see the steps as below.
1. Assign an element to an evacuation input control:
1. Use Evacuation Input components.
2. By using the Evacuation Input component, you can control other logic components. The logic
signal is coming from the Evacuation Input component and is going to any other input pins of the
logic component as you choose. Please refer to
They can be used in the UGA mode, triggered by a change of the voltage polarization. To set
this option,please use the Evacuation Input component, see more details on
3.1.20.2 Contact Output
The IDA8C/S processor has the logic output channels for closing/opening a circuit of an external device.
There are two ways to configure it, see the steps as below,
1. Assign an element to the evacuation output control.
