Altigen ACC 6.7 Administration Manual Download | Manualshive

Page: 264 / 462

background image

Chapter 19: Hunt Group Configuration

250

MAXCS ACC 6.7 Administration Manual

Figure 119. Huntgroup Configuration, Notification tab

Individual users can also configure

Message Notification

within the AltiGen Voice Mail

System.

Note:

You can use

Apply to

to apply mailbox settings to one, some, or all hunt groups.

See “Apply to Button” on page 244 for more information on using

Apply to

.

Setting the Message Types for Notification

Select the types of messages for which the hunt group user will be notified:

•

None

—selected, the user is

not

notified with a call regarding newly received

messages. Selecting this option does not prevent the user from getting message
waiting indicators or stutter dial tone when new messages are received.

•

Urgent Voice Messages Only

•

All Voice Messages

Please note that the system will start notification as soon as it enters non-business hours
under the following conditions:

•

Extension is set to notify

Urgent Voice Message Only

•

Notification is set to

Non-Business Hours

•

Voice mail is received during business hours and is marked urgent

•

Extension user does not check the urgent message

Setting the Type of Notification

There are four options for sending the notification or reminder message:

phone

,

pager

,

extension

or

custom application (Custom App)

.

•

Extension

- to use the Extension option, select the

Extension

radio button, then

type the extension number into the text box.

«
...
262
263
264
265
266
...
»

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACC 6.7

Brand: LevelOne Pages: 88

Brand: Olive Pages: 19

Brand: Black Box Pages: 30

SuperServer 6029U-TR25M

Brand: Supermicro Pages: 151

Brand: Zeiss Pages: 12

DPR-1260 - RangeBooster G Multifunction Print Server

Brand: D-Link Pages: 55

Brand: D-Link Pages: 49

ProLiant BL460c Gen8

Brand: HP Pages: 84

Proliant BL480c

Brand: HP Pages: 65

ProLiant BL420c

Brand: HP Pages: 88

Brand: HP Pages: 34

ProLiant BL685c G5

Brand: HP Pages: 23

ProLiant BL660c Gen 9

Brand: HP Pages: 3

ProLiant BL460c G7

Brand: HP Pages: 74

ProLiant BL495c G6

Brand: HP Pages: 90

ProLiant BL685c G7

Brand: HP Pages: 67

ProLiant BL280c Generation 6 (G6)

Brand: HP Pages: 36

ProLiant BL620c Generation 7

Brand: HP Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands