Altigen ACC 6.7 Administration Manual Download | Manualshive

Page: 107 / 462

background image

Chapter 7: Auto Attendant Configuration

MAXCS ACC 6.7 Administration Manual 93

To install professionally recorded phrases or prompts:

1. Assign a prompt number to each prompt you would like recorded. Or give the prompt

a unique identifying name. AltiGen-supplied phrases are numbered, but phrases
don’t have to be numbered.

2. Submit your prompt script and prompt name to the recording studio.
3. Instruct the recording studio to record prompts in either 8KHz or 11.025KHz mono

in the WAV format.

4. Ask the studio to convert the WAV file(s) into the proper MAXCS format.

•

If using Worldly Voices, this conversion is done for you.

•

If you are using a studio other than Worldly Voices, use the Voice File Conversion
utility. This utility converts an audio file recorded at either 8KHz or 11.025KHz in
the WAV format to an MAXCS-playable audio file.

5. Once you receive the prompts in the MAXCS format, place them in the

C:\PostOffice\phrases\LangCustom

directory on the gateway that is running

AltiServ.

Your prompts are now ready to be used.

«
...
105
106
107
108
109
...
»

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACC 6.7

Network Space MAX

Brand: LaCie Pages: 2

8649 - Eserver xSeries 225

Brand: IBM Pages: 194

Brand: Axis Pages: 66

MediaGrid ContentServer 3000

Brand: Omneon Pages: 2

Brand: Sun Microsystems Pages: 12

Brand: QNAP Pages: 69

Brand: IBM Pages: 5

Brand: Black Box Pages: 60

Brand: Lindy Pages: 2

Brand: Inspur Pages: 135

Brand: VC Pages: 100

Brand: IBM Pages: 8

3C16115-US - SuperStack 3 Webcache 1000

Brand: 3Com Pages: 176

Brand: Intel Pages: 77

Brand: Intel Pages: 179

Brand: TROY Group Pages: 62

Sun Server X4-4

Brand: Oracle Pages: 148

Brand: Xblue Networks Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands