Altigen ACC 6.7 Administration Manual Download Page 2 | Manualshive

Page: 2 / 462

background image

NOTICE

: While every effort has been made to ensure accuracy, AltiGen Communications, Inc., will not

be liable for technical or editorial errors or omissions contained within the documentation. The
information contained in this documentation is subject to change without notice.
This documentation may be used only in accordance with the terms of the AltiGen Communications, Inc.,
License Agreement.

MAX Communication Server, MaxAdministrator, MaxCommunicator, MaxAgent, MaxSupervisor,
MaxOutlook, MaxInSight, MaxCall, Enterprise Manager, AltiServ, AltiLink, AltiConsole, VRPlayer,
Zoomerang, IPTalk, Alti-Mobile Extension, InTouch Dialer, AltiReport, and SuperQ are trademarks or
registered trademarks of AltiGen Communications, Inc. All other brand names mentioned are trademarks
or registered trademarks of their respective manufacturers.
AltiGen's products are protected under one or more of the following U.S. patents, with other U.S. patents
pending: 6532230; 6192344; 6292549; 6493439; 6909780; 6738465; 6754202; 6766006; 6928078;
6909709; 6956848; 7058047; 7013007; 7027578; 7280649; 7308092.

AltiGen Communications, Inc.
410 East Plumeria Dr.
San Jose, CA 95134
Telephone: 888-AltiGen (258-4436)
Fax: 408-597-9020
E-mail: [email protected]
Web site: www.altigen.com

Copyright © AltiGen Communications, Inc. 2011. All rights reserved.

«
1
2
3
4
...
»

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACC 6.7

Altos R700 Series

Brand: Acer Pages: 80

Altos G700 series

Brand: Acer Pages: 14

Brand: Acer Pages: 103

Altos R720 Series

Brand: Acer Pages: 104

ML-2010 - B/W Laser Printer

Brand: Samsung Pages: 25

digitalSTROM-Server

Brand: aizo Pages: 2

8480 - Eserver xSeries 205

Brand: IBM Pages: 174

Brand: AXIOMTEK Pages: 58

System X Series

Brand: IBM Pages: 6

HES-V1000 - Home Entertainment Server

Brand: Sony Pages: 155

Brand: Supermicro Pages: 96

Brand: Supermicro Pages: 130

Brand: Supermicro Pages: 124

Brand: Viavi Pages: 12

G4-40G-100-384T

Brand: Viavi Pages: 12

Brand: Supermicro Pages: 76

Brand: Supermicro Pages: 79

Brand: AMX Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands