manualshive.com logo in svg

Altigen ACC 6.7, Administration Manual

The Altigen ACC 6.7 Administration Manual is an essential resource for effectively managing your Altigen ACC 6.7 system. Download this comprehensive manual for free from our website, providing step-by-step instructions and insights into configuration and administration. Empower yourself with the knowledge to optimize your Altigen ACC 6.7 experience.

Share
Download
background image

Chapter 6:  Voice Mail Configuration

MAXCS ACC 6.7 Administration Manual  79

Setting Message Recording Options 

Set voice mail message recording parameters:

Setting Exchange Integration Options 

Set Exchange integration options. Access to these options requires an AltiGen Exchange 
Integration License. To assign this license to an extension, see “Assign Exchange 
Integration License” on page 197.
If you are opting to use Exchange’s Speech Enabled Voice Mail features or Unified 
Messaging, Exchange Server and AltiServ need to be installed on the same domain with 
a network throughput rate of no less than 100 Mbps. 
For Exchange, you must configure the extension number in the Exchange user account 
to be the same as the AltiServ extension number.
Complete configuration details are given in the chapter “Microsoft Exchange Integration” 
on page 363.
You may choose an option when you install AltiServ, and you may change the option 
later without having to shut down AltiServ.

Warn Expiration of 
Saved Messages

If checked, the system warns the user that saved messages 
will be deleted due to their retention time expiring. The 
message is given the day before the messages are 
automatically deleted, and the user then has the option to 
either keep or delete the messages. By default, this feature is 
enabled.

Note:

If this feature is disabled, saved messages are deleted 

automatically without warning when they expire.

Parameter

Description

Minimum Recording 
Length

Sets the minimum length in seconds for any recording 
(incoming voice mail message, personal greeting, system 
prompts, introductions to forwarded voice mails). This can be 
from 1–5 seconds, or 0, which means no minimum.
All recordings that are shorter than the designated Minimum 
Recording length are deleted. This feature is recommended 
when users receive many short, empty voice mail messages on 
a regular basis and would like them automatically deleted. 

Pause Detect Length 

Selected, this feature causes the deletion of pauses in 
messages. The default pause detect length is 

500 ms

. The 

pause detect can be disabled by deselecting the check box, or 
the length can be set to a value between 

200–2000 ms (.2–

2 seconds)

.

Parameter

Description

Disabled 

Disables Exchange integration. 

Parameter

Description

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACC 6.7

IBM 610 Technical Overview And Introduction preview
610
Brand: IBM Pages: 40
A10 Networks AX Series Deployment Manual preview
AX Series
Brand: A10 Networks Pages: 17
IBM BladeCenter QS20 Installation And User Manual preview
BladeCenter QS20
Brand: IBM Pages: 92
IBM BladeCenter JS20 Maintenance And Troubleshooting Manual preview
BladeCenter JS20
Brand: IBM Pages: 218
IBM HS21 - BladeCenter - 8853 User Manual preview
HS21 - BladeCenter - 8853
Brand: IBM Pages: 80
IBM 8835 - Eserver 325 - 1 GB RAM Option Installation Manual preview
8835 - Eserver 325 - 1 GB RAM
Brand: IBM Pages: 62
IBM 8835 - Eserver 325 - 1 GB RAM Technical Update preview
8835 - Eserver 325 - 1 GB RAM
Brand: IBM Pages: 2
IBM 8676 - Eserver xSeries 335 Installation Manual preview
8676 - Eserver xSeries 335
Brand: IBM Pages: 92
IBM 8670 - Eserver xSeries 345 User Manual preview
8670 - Eserver xSeries 345
Brand: IBM Pages: 60
IBM 8647 - Eserver xSeries 225 Maintenance And Troubleshooting Manual preview
8647 - Eserver xSeries 225
Brand: IBM Pages: 182
IBM 8480 - Eserver xSeries 205 User Manual preview
8480 - Eserver xSeries 205
Brand: IBM Pages: 64
IBM 79463AU Brochure preview
79463AU
Brand: IBM Pages: 2
IBM 71455RU Installation And User Manual preview
71455RU
Brand: IBM Pages: 136
IBM RS/6000 SP Handbook preview
RS/6000 SP
Brand: IBM Pages: 480
IBM 450 xSeries User Manual preview
450 xSeries
Brand: IBM Pages: 68
IBM @Server pSeries 630 6C4 Installation Manual preview
@Server pSeries 630 6C4
Brand: IBM Pages: 180
IBM eServer 380 xSeries Installation Manual preview
eServer 380 xSeries
Brand: IBM Pages: 54
Paradyne FrameSaver SLV 9126 Installation Instructions Manual preview
FrameSaver SLV 9126
Brand: Paradyne Pages: 24

Brands by name

Popular brands

Load more brands