manualshive.com logo in svg

Altigen ACC 6.7, Administration Manual

The Altigen ACC 6.7 Administration Manual is an essential resource for effectively managing your Altigen ACC 6.7 system. Download this comprehensive manual for free from our website, providing step-by-step instructions and insights into configuration and administration. Empower yourself with the knowledge to optimize your Altigen ACC 6.7 experience.

Share
Download
background image

Chapter 11:  Board Configuration

MAXCS ACC 6.7 Administration Manual  135

Figure 72.  H323 Configuration 

You can change the following parameters:

•

FastStart Enabled

: The 

FastStart Enabled

 option reduces the number of H.323 

messages to be sent between two H.323 devices when initiating a call, thus reducing 
the time needed to establish a call. There may be a compatibility issue with firewall 
or NAT devices, if you select this option.

•

Max Tie-Trunk Channel

: Sets the maximum number of trunk channels for this 

board in increments of 4, from 4 to 96. You need to reboot the MAXCS system after 
the maximum trunk channel number is changed.

Configuring Virtual Board HMCP

This section is for a Multi-Gateway Softswitch with an HMCP media server installation 
only. A single all-in-one system does not require configuration of this board. 
Host Media Control Processing (HMCP) is a virtual board that uses an Intel CPU to provide 
the following functions:
1. Process VoIP Media Stream

•

Encode, decode, and transcode voice stream

•

Detect and generate tone for IP devices 

•

Play music when device is on hold

•

Process IP paging

2. Play and Record Voice Files

•

Announce system and queue phrases

•

Process auto attendant

•

Process voice mail 

•

Call recording for IP extensions

3. Provide Conferencing Resources

•

Station conference

•

Meet-Me conference

•

Barge-in/silent monitor/coaching

If you change the maximum 
number of trunk channels, 
you need to reboot the 
MAXCS system.

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACC 6.7

IBM Enterprise Server S80 User Manual preview
Enterprise Server S80
Brand: IBM Pages: 282
Aaeon AIOT-ILRA01 User Manual preview
AIOT-ILRA01
Brand: Aaeon Pages: 38
IEI Technology PUZZLE-IN003A User Manual preview
PUZZLE-IN003A
Brand: IEI Technology Pages: 89
IBM System x3250 M3 Type 4251 Manual preview
System x3250 M3 Type 4251
Brand: IBM Pages: 32
Newtec NOP1840 PEP-Box User Manual preview
NOP1840 PEP-Box
Brand: Newtec Pages: 96
Supermicro SUPERSERVER 1015B-3 User Manual preview
SUPERSERVER 1015B-3
Brand: Supermicro Pages: 98
Asus ASMB7-iKVM User Manual preview
ASMB7-iKVM
Brand: Asus Pages: 98
Asus ASMB4-IKVM User Manual preview
ASMB4-IKVM
Brand: Asus Pages: 84
Cisco Aironet 1500 Series Datasheet preview
Aironet 1500 Series
Brand: Cisco Pages: 8
Cisco 7835-H2 - Media Convergence Server Datasheet preview
7835-H2 - Media Convergence Server
Brand: Cisco Pages: 8
Cisco APP1000 - One Application Server Appliance Installation And Administration Manual preview
APP1000 - One Application Server Appliance
Brand: Cisco Pages: 20
Cisco APIC L3 Installation And Service Manual preview
APIC L3
Brand: Cisco Pages: 130
GRASS VALLEY HDMA-4000SYNC Datasheet preview
HDMA-4000SYNC
Brand: GRASS VALLEY Pages: 2
Bosanova RBT-402 Specifications preview
RBT-402
Brand: Bosanova Pages: 2
BayTech LASERSHARE PS-MIO Owner'S Manual preview
LASERSHARE PS-MIO
Brand: BayTech Pages: 133
360 Systems MAXX-2420-EX Operation Manual preview
MAXX-2420-EX
Brand: 360 Systems Pages: 148
Intel S1200V3RP Technical Product Specification preview
S1200V3RP
Brand: Intel Pages: 270
Planet ICS-2200T Quick Installation Manual preview
ICS-2200T
Brand: Planet Pages: 16

Brands by name

Popular brands

Load more brands