Altigen ACC 6.7 Administration Manual Download | Manualshive

Page: 80 / 462

background image

Chapter 4: System Configuration

66

MAXCS ACC 6.7 Administration Manual

Activity

The

Activity

configuration tab is used to configure activity codes that can be displayed

at AltiConsole when the extension user is absent. MaxCommunicator users, MaxAgent
users, and AltiGen IP phone users can select from these activity codes to let others know
where they are when they are away from their desks (meeting, business travel, etc.).
A greeting associated with the activity can be recorded and played to the caller. When
the user changes the Activity, the extension’s greeting is also automatically changed to
the greeting associated with this activity.
To access

Activity

configuration, select

System > System Configuration

, then click

the

Activity

tab.

There are a total of nine activity codes; the first six are pre-configured as follows:

1 - System Default (plays the system greeting)
2 - Personal (plays the personal greeting)
3 - Meeting
4 - Away From Desk
5 - Business Travel
6 - Personal Time Off

The remaining three activity codes (7, 8, 9) are not assigned and can be customized by
the administrator. To customize an activity code, click the activity code and click

Edit

.

In the

Edit Activity

dialog box, enter name of the Activity and click

OK

.

Feature Profiles

Select

System > System Configuration

, then click the

Feature Profiles

tab to

configure feature profiles.

«
...
78
79
80
81
82
...
»

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACC 6.7

Brand: IBM Pages: 908

Brand: Xerox Pages: 8

Brand: B&B Pages: 55

Brand: TAPKO Pages: 2

ProLiant ML110 Gen 10

Brand: HPE Pages: 5

SUPERSERVER 5014C-MT

Brand: Supero Pages: 112

Brand: IBM Pages: 96

Brand: Syncronorm Pages: 17

UCS Invicta C3124SA

Brand: Cisco Pages: 60

Brand: Cisco Pages: 54

UCS Invicta C3124SA

Brand: Cisco Pages: 40

Brand: Cisco Pages: 132

Brand: Cisco Pages: 46

Brand: Cisco Pages: 35

Brand: Cisco Pages: 188

Brand: TYAN Pages: 80

B8236G70W8HR-HE

Brand: TYAN Pages: 84

Brand: TYAN Pages: 82

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands