Altigen ACC 6.7 Administration Manual Download | Manualshive

Page: 449 / 462

background image

MAXCS ACC 6.7 Administration Manual 435

A

P P E N D I X

D

Technical Support & Product Repair

Services

This appendix describes:

•

AltiGen technical support policy and procedures

•

Product repair

•

Technical training for administrators

Technical Support

Eligibility

: AltiGen provides technical support to Authorized AltiGen dealers and

distributors only.
End user customers, please contact your Authorized AltiGen Dealer for technical support.

How To Reach AltiGen Technical Support

Authorized AltiGen dealers and distributors

may contact AltiGen technical support

by any of the following methods:

•

You may request technical support on AltiGen’s dealer web site, at https://
dealer.altigen.com. Open a case on this site, and a Technical Support representative
will respond within one business day.

•

Call 888-ALTIGEN, option 5, or 408-597-9000, option 5,

and follow the prompts.

Your call will be answered by one of AltiGen’s Technical Support Representatives or
routed to the Technical Support Message Center if no one is available to answer your
call.
Technical support hours are 5:00 a.m. to 5:00 p.m., PST, Monday through Friday,
except holidays.
If all representatives are busy, your call will be returned in the order it was received,
within four hours under normal circumstances. Outside AltiGen business hours, only
urgent calls will be returned on the same day (within one hour). Non-urgent calls will
be returned on the next business day.
Please be ready to supply the following information:

•

Dealer ID

•

AltiGen Certified Engineer ID

•

Product serial number

«
...
447
448
449
450
451
...
»

Summary of Contents for ACC 6.7















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ACC 6.7

QS21 - BladeCenter - 0792

Brand: IBM Pages: 110

SX-2000A Series

Brand: GDC Pages: 185

Vlinx Serial Servers ESP901E

Brand: B&B Electronics Pages: 92

iDataPlex dx320 6385

Brand: IBM Pages: 60

Brand: Lantech Pages: 49

Brand: Thecus Pages: 120

Modbus Server-Cerberus ISO1745

Brand: IntesisBox Pages: 5

Brand: Raidon Pages: 20

Brand: Interface Masters Pages: 34

Express5800/R320f-E4

Brand: NEC Pages: 88

Brand: Cavalry Pages: 16

Brand: Cisco Pages: 2

Alcatel-Lucent OXO Connect Compact

Brand: Nokia Pages: 216

Brand: QNAP Pages: 55

Brand: Synology Pages: 16

Brand: Synology Pages: 33

Brand: Synology Pages: 20

Brand: Synology Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands